Matin Amani

Near-unity photoluminescence quantum yield in MoS2

Brighter molybdenum layers The confined layers of molybdenum disulphide (MoS2) exhibit photoluminescence that is attractive for optolectronic applications. In practice, efficiencies are low, presumably because defects trap excitons before they can recombine and radiate light. Amani et al. show that treatment of monolayer MoS2 with a nonoxidizing organic superacid, bis(trifluoromethane) sulfonimide, increased luminescence efficiency in excess of 95%. The enhancement mechanism may be related to the shielding of defects, such as sulfur vacancies. Science, this issue p. 1065 Superacid treatment enhances the luminescence efficiency of monolayer molybdenum disulfide from 1% to >95%. Two-dimensional (2D) transition metal dichalcogenides have emerged as a promising material system for optoelectronic applications, but their primary figure of merit, the room-temperature photoluminescence quantum yield (QY), is extremely low. The prototypical 2D material molybdenum disulfide (MoS2) is reported to have a maximum QY of 0.6%, which indicates a considerable defect density. Here we report on an air-stable, solution-based chemical treatment by an organic superacid, which uniformly enhances the photoluminescence and minority carrier lifetime of MoS2 monolayers by more than two orders of magnitude. The treatment eliminates defect-mediated nonradiative recombination, thus resulting in a final QY of more than 95%, with a longest-observed lifetime of 10.8 ± 0.6 nanoseconds. Our ability to obtain optoelectronic monolayers with near-perfect properties opens the door for the development of highly efficient light-emitting diodes, lasers, and solar cells based on 2D materials.

Strain and structure heterogeneity in MoS2 atomic layers grown by chemical vapour deposition

Monolayer molybdenum disulfide (MoS2) has attracted tremendous attention due to its promising applications in high-performance field-effect transistors, phototransistors, spintronic devices and nonlinear optics. The enhanced photoluminescence effect in monolayer MoS2 was discovered and, as a strong tool, was employed for strain and defect analysis in MoS2. Recently, large-size monolayer MoS2 has been produced by chemical vapour deposition, but has not yet been fully explored. Here we systematically characterize chemical vapour deposition-grown MoS2 by photoluminescence spectroscopy and mapping and demonstrate non-uniform strain in single-crystalline monolayer MoS2 and strain-induced bandgap engineering. We also evaluate the effective strain transferred from polymer substrates to MoS2 by three-dimensional finite element analysis. Furthermore, our work demonstrates that photoluminescence mapping can be used as a non-contact approach for quick identification of grain boundaries in MoS2.

Electrical performance of monolayer MoS2 field-effect transistors prepared by chemical vapor deposition

Molybdenum disulfide (MoS2) field effect transistors (FET) were fabricated on atomically smooth large-area single layers grown by chemical vapor deposition. The layer qualities and physical properties were characterized using high-resolution Raman and photoluminescence spectroscopy, scanning electron microscopy, and atomic force microscopy. Electronic performance of the FET devices was measured using field effect mobility measurements as a function of temperature. The back-gated devices had mobilities of 6.0 cm2/V s at 300 K without a high-κ dielectric overcoat and increased to 16.1 cm2/V s with a high-κ dielectric overcoat. In addition the devices show on/off ratios ranging from 105 to 109.

Temperature-dependent phonon shifts in monolayer MoS2

We present a combined experimental and computational study of two-dimensional molybdenum disulfide and the effect of temperature on the frequency shifts of the Raman-active E2g and A1g modes in the monolayer. While both peaks show an expected red-shift with increasing temperature, the frequency shift is larger for the A1g mode than for the E2g mode. This is in contrast to previously reported bulk behavior, in which the E2g mode shows a larger frequency shift with temperature. The temperature dependence of these phonon shifts is attributed to the anharmonic contributions to the ionic interaction potential in the two-dimensional system.

Recombination Kinetics and Effects of Superacid Treatment in Sulfur- and Selenium-Based Transition Metal Dichalcogenides

Optoelectronic devices based on two-dimensional (2D) materials have shown tremendous promise over the past few years; however, there are still numerous challenges that need to be overcome to enable their application in devices. These include improving their poor photoluminescence (PL) quantum yield (QY) as well as better understanding of exciton-based recombination kinetics. Recently, we developed a chemical treatment technique using an organic superacid, bis(trifluoromethane)sulfonimide (TFSI), which was shown to improve the quantum yield in MoS2 from less than 1% to over 95%. Here, we perform detailed steady-state and transient optical characterization on some of the most heavily studied direct bandgap 2D materials, specifically WS2, MoS2, WSe2, and MoSe2, over a large pump dynamic range to study the recombination mechanisms present in these materials. We then explore the effects of TFSI treatment on the PL QY and recombination kinetics for each case. Our results suggest that sulfur-based 2D materials are amenable to repair/passivation by TFSI, while the mechanism is thus far ineffective on selenium based systems. We also show that biexcitonic recombination is the dominant nonradiative pathway in these materials and that the kinetics for TFSI treated MoS2 and WS2 can be described using a simple two parameter model.

Defective TiO2 with high photoconductive gain for efficient and stable planar heterojunction perovskite solar cells

Formation of planar heterojunction perovskite solar cells exhibiting both high efficiency and stability under continuous operation remains a challenge. Here, we show this can be achieved by using a defective TiO2 thin film as the electron transport layer. TiO2 layers with native defects are deposited by electron beam evaporation in an oxygen-deficient environment. Deep-level hole traps are introduced in the TiO2 layers and contribute to a high photoconductive gain and reduced photocatalytic activity. The high photoconductivity of the TiO2 electron transport layer leads to improved efficiency for the fabricated planar devices. A maximum power conversion efficiency of 19.0% and an average PCE of 17.5% are achieved. In addition, the reduced photocatalytic activity of the TiO2 layer leads to enhanced long-term stability for the planar devices. Under continuous operation near the maximum power point, an efficiency of over 15.4% is demonstrated for 100 h.

Electrical Transport Properties of Polycrystalline Monolayer Molybdenum Disulfide

Semiconducting MoS2 monolayers have shown many promising electrical properties, and the inevitable polycrystallinity in synthetic, large-area films renders understanding the effect of structural defects, such as grain boundaries (GBs, or line-defects in two-dimensional materials), essential. In this work, we first examine the role of GBs in the electrical-transport properties of MoS2 monolayers with varying line-defect densities. We reveal a systematic degradation of electrical characteristics as the line-defect density increases. The two common MoS2 GB types and their specific roles are further examined, and we find that only tilt GBs have a considerable effect on the MoS2 electrical properties. By examining the electronic states and sources of disorder using temperature-dependent transport studies, we adopt the Anderson model for disordered systems to explain the observed transport behaviors in different temperature regimes. Our results elucidate the roles played by GBs in different scenarios and give insights into their underlying scattering mechanisms.

Asymmetric Growth of Bilayer Graphene on Copper Enclosures Using Low-Pressure Chemical Vapor Deposition

In this work, we investigated the growth mechanisms of bilayer graphene on the outside surface of Cu enclosures at low pressures. We observed that the asymmetric growth environment of a Cu enclosure can yield a much higher (up to 100%) bilayer coverage on the outside surface as compared to the bilayer growth on a flat Cu foil, where both sides are exposed to the same growth environment. By simultaneously examining the graphene films grown on both the outside and inside surfaces of the Cu enclosure, we find that carbon can diffuse from the inside surface to the outside via exposed copper regions on the inside surface. The kinetics of this process are examined by coupling the asymmetric growth between the two surfaces through a carbon diffusion model. Finally, using these results, we show that the coverage of bilayer graphene can be tuned simply by changing the thickness of the Cu foil, further confirming our model of carbon delivery through the Cu foil.

Engineering Light Outcoupling in 2D Materials

When light is incident on 2D transition metal dichalcogenides (TMDCs), it engages in multiple reflections within underlying substrates, producing interferences that lead to enhancement or attenuation of the incoming and outgoing strength of light. Here, we report a simple method to engineer the light outcoupling in semiconducting TMDCs by modulating their dielectric surroundings. We show that by modulating the thicknesses of underlying substrates and capping layers, the interference caused by substrate can significantly enhance the light absorption and emission of WSe2, resulting in a ∼11 times increase in Raman signal and a ∼30 times increase in the photoluminescence (PL) intensity of WSe2. On the basis of the interference model, we also propose a strategy to control the photonic and optoelectronic properties of thin-layer WSe2. This work demonstrates the utilization of outcoupling engineering in 2D materials and offers a new route toward the realization of novel optoelectronic devices, such as 2D LEDs and solar cells.

High Luminescence Efficiency in MoS2 Grown by Chemical Vapor Deposition

One of the major challenges facing the rapidly growing field of two-dimensional (2D) transition metal dichalcogenides (TMDCs) is the development of growth techniques to enable large-area synthesis of high-quality materials. Chemical vapor deposition (CVD) is one of the leading techniques for the synthesis of TMDCs; however, the quality of the material produced is limited by defects formed during the growth process. A very useful nondestructive technique that can be utilized to probe defects in semiconductors is the room-temperature photoluminescence (PL) quantum yield (QY). It was recently demonstrated that a PL QY near 100% can be obtained in MoS2 and WS2 monolayers prepared by micromechanical exfoliation by treating samples with an organic superacid: bis(trifluoromethane)sulfonimide (TFSI). Here we have performed a thorough exploration of this chemical treatment on CVD-grown MoS2 samples. We find that the as-grown monolayers must be transferred to a secondary substrate, which releases strain, to obtain high QY by TFSI treatment. Furthermore, we find that the sulfur precursor temperature during synthesis of the MoS2 plays a critical role in the effectiveness of the treatment. By satisfying the aforementioned conditions we show that the PL QY of CVD-grown monolayers can be improved from ∼0.1% in the as-grown case to ∼30% after treatment, with enhancement factors ranging from 100 to 1500× depending on the initial monolayer quality. We also found that after TFSI treatment the PL emission from MoS2 films was visible by eye despite the low absorption (5-10%). The discovery of an effective passivation strategy will speed the development of scalable high-performance optoelectronic and electronic devices based on MoS2.