Norinsan Kamil Othman

A review on radiation-induced nucleation and growth of colloidal metallic nanoparticles

This review presents an introduction to the synthesis of metallic nanoparticles by radiation-induced method, especially gamma irradiation. This method offers some benefits over the conventional methods because it provides fully reduced and highly pure nanoparticles free from by-products or chemical reducing agents, and is capable of controlling the particle size and structure. The nucleation and growth mechanism of metallic nanoparticles are also discussed. The competition between nucleation and growth process in the formation of nanoparticles can determine the size of nanoparticles which is influenced by certain parameters such as the choice of solvents and stabilizer, the precursor to stabilizer ratio, pH during synthesis, and absorbed dose.

Radiolytic Formation of Fe3O4 Nanoparticles: Influence of Radiation Dose on Structure and Magnetic Properties

Colloidal Fe3O4 nanoparticles were synthesized using a gamma-radiolysis method in an aqueous solution containing iron chloride in presence of polyvinyl alcohol and isopropanol as colloidal stabilizer and hydroxyl radical scavenger, respectively. Gamma irradiation was carried out in a 60Co gamma source chamber at different absorbed doses. Increasing the radiation dose above a certain critical dose (100 kGy) leads to particle agglomeration enhancement, and this can influence the structure and crystallinity, and consequently the magnetic properties of the resultant particles. The optimal condition for formation of Fe3O4 nanoparticles with a uniform and narrow size distribution occurred at a dose of 100 kGy, as confirmed by X-ray diffractometry and transmission electron microscopy. A vibrating sample magnetometry study showed that, when radiation dose increased, the saturation and remanence magnetization decreased, whereas the coercivity and the remanence ratio increased. This magnetic behavior results from variations in crystallinity, surface effects, and particle size effects, which are all dependent on the radiation dose. In addition, Fourier transform infrared spectroscopy was performed to investigate the nature of the bonds formed between the polymer chains and the metal surface at different radiation doses.

High Sensitivity pH Sensor Based on Porous Silicon (PSi) Extended Gate Field-Effect Transistor

In this study, porous silicon (PSi) was prepared and tested as an extended gate field-effect transistor (EGFET) for pH sensing. The prepared PSi has pore sizes in the range of 500 to 750 nm with a depth of approximately 42 µm. The results of testing PSi for hydrogen ion sensing in different pH buffer solutions reveal that the PSi has a sensitivity value of 66 mV/pH that is considered a super Nernstian value. The sensor considers stability to be in the pH range of 2 to 12. The hysteresis values of the prepared PSi sensor were approximately 8.2 and 10.5 mV in the low and high pH loop, respectively. The result of this study reveals a promising application of PSi in the field for detecting hydrogen ions in different solutions.

Influence of rotational speed on mechanical properties of friction stir lap welded 6061-T6 Al alloy

The effect of rotational speed on macro and microstructures, hardness, lap shear performance and failure mode of friction stir lap welding on AA6061-T6 Al alloy with 5 mm in thickness was studied by field-emission scanning electron microscopy (FE-SEM). The results represent much closer hardness distribution in the upper and lower plates at the lowest rotational speed. It indicates the Fe-compounds in the fracture surface of the nugget zone by EDX.

Some thoughts on bondability and strength of gold wire bonding

The bonding mechanisms of gold, to give the desired strength of wire bonding, still require detailed investigation, including establishing adequate and reliable testing procedures. The current practices for analysing the mechanisms of wire bonding are inadequate and do not provide a comprehensive picture. This is because the focus of the tests is not clear, which causes variation in the results obtained, changing the conclusions about the responsible mechanism. Furthermore, as the size of Au wire bonds decreases, the mechanism responsible for thermosonic Au wire bonding may change. This paper provides a comprehensive analysis of the current and possible future methods for elaborating the bonding mechanism and strength of thermosonic Au wire bonds. We discuss the testing methods, their limitations and advantages, and suggest ways in which they can be improved.

Amperometric Non-Enzymatic Hydrogen Peroxide Sensor Based on Aligned Zinc Oxide Nanorods

Zinc oxide (ZnO) nanorods (NRs) have been synthesized via the hydrothermal process. The NRs were grown over a conductive glass substrate. A non-enzymatic electrochemical sensor for hydrogen peroxide (H2O2), based on the prepared ZnO NRs, was examined through the use of current-voltage measurements. The measured currents, as a function of H2O2 concentrations ranging from 10 μM to 700 μM, revealed two distinct behaviours and good performance, with a lower detection limit (LOD) of 42 μM for the low range of H2O2 concentrations (first region), and a LOD of 143.5 μM for the higher range of H2O2 concentrations (second region). The prepared ZnO NRs show excellent electrocatalytic activity. This enables a measurable and stable output current. The results were correlated with the oxidation process of the H2O2 and revealed a good performance for the ZnO NR non-enzymatic H2O2 sensor.

Corrosion behavior of friction stir welded lap joints of AA6061-T6 aluminum alloy

In this work, the corrosion behaviors of friction-stir lap welding of 6061-T6 Al-alloy are studied. The friction-stir lap welding was performed under different welding conditions (rotation speed and welding speed). The corrosion behavior of the parent alloy, the weld nugget zone (WNZ), and the heat affected zone (HAZ) of each welded sample working as an electrode, were investigated by the Tafel polarization test in 3.5 wt. (%) NaCl at ambient temperature. The morphology of the corroded surface of each region was analyzed by scanning electron microscopy together with energy dispersive spectroscopy (SEM-EDS). The results showed that the corrosion resistance of the parent alloy was better than the WNZ and the HAZ in both welding conditions. Localized pit dissolution and intergranular corrosion were the dominant corrosion types observed in the parent alloy, WNZ, and HAZ. The parent alloy, WNZ, and HAZ exhibited similar corrosion potentials (Ecorr) after T6 heat treatment. This treatment had a better effect on the corrosion resistance of the welded regions than the parent alloy.

Corrosion evaluation of friction stir welded lap joints of AA6061-T6 aluminum alloy

Abstract Corrosion behavior of friction stir lap welded AA6061-T6 aluminum alloy was investigated by immersion tests in sodium chloride + hydrogen peroxide solution. Electrochemical measurement by cyclic potentiodynamic polarization, scanning electron microscopy, and energy dispersive spectroscopy were employed to characterize corrosion morphology and to realize corrosion mechanism of weld regions as opposed to the parent alloy. The microstructure and shear strength of welded joint were fully investigated. The results indicate that, compared with the parent alloy, the weld regions are susceptible to intergranular and pitting attacks in the test solution during immersion time. The obtained results of lap shear testing disclose that tensile shear strength of the welds is 128 MPa which is more than 60% of the strength of parent alloy in lap shear testing. Electrochemical results show that the protection potentials of the WNZ and HAZ regions are more negative than the pitting potential. This means that the WNZ and HAZ regions do not show more tendencies to pitting corrosion. Corrosion resistance of parent alloy is higher than that for the weldments, and the lowest corrosion resistance is related to the heat affected zone. The pitting attacks originate from the edge of intermetallic particles as the cathode compared with the Al matrix due to their high self-corrosion potential. It is supposed that by increasing intermetallic particle distributed throughout the matrix of weld regions, the galvanic corrosion couples are increased, and hence decrease the corrosion resistance of weld regions.

A Study on the UV Photoresponse of Hydrothermally Grown Zinc Oxide Nanorods With Different Aspect Ratios

We report on the effect of the aspect ratio of zinc oxide (ZnO) nanorods (NRs) prepared by the hydrothermal process. It was found that increasing the precursor molar amount resulted in the decrease of the aspect ratio of ZnO NRs. Furthermore, the aspect ratios showed a significant effect on the structural and optical properties of the prepared ZnO NRs. The ZnO NRs were fabricated into a metal-semiconductor-metal (MSM) UV photodetector. The performances of the prepared MSM ZnO NRs were also studied, and the high aspect ratio showed that the highest responsivity had a value of 33 A/W at a bias voltage of 5 V and a wavelength of 380 nm. The responsivity, rise time, and full time of the prepared ZnO NRs showed a trend of behavior as the molar amount of the precursor was varied.

Electrochemical Migration Behaviours of Low Silver Content Solder Alloy SAC 0307 on Printed Circuit Boards (PCBs) in NaCl Solution

Electrochemical migration (ECM) of solder joining can result in the growth of a metal deposit with dendrite structure from cathode to anode. In electronic device, this phenomenon potentially leads to the incompetence or failure of whole devices. In this paper, the ECM behaviour of printed circuit boards (PCBs) with SAC 0307, one of the low-cost lead-free solder alloys with less silver content, has been studied. The corrosion behaviour of SAC 0307 has been investigated by using sodium chloride solution in different concentrations which is between 0.01 M to 1.0 M as a medium. A Water Drop Test (WDT) was carried out and the time-to-failure of each sample has been recorded. After WDT test, the dendrite phase was identified using Variable Pressure Scanning Electron Microscope (VPSEM) with Energy Dispersive X-ray Spectroscopy (EDX) and X-ray Photoelectron Spectroscopy (XPS) to investigate its surface morphology and corrosion products. As results, it has been found that the corrosion susceptibility of SAC 0307 is greatly influenced by the concentration of the medium solution used. The voltage drop occurred was due to the dendrite grew at the cathode electrode on the PCBs and expanded to the anode electrode, indicating a significant effect of aggressive behaviour of the medium used. The rate of the dendrite growth was affected by the concentration of the medium used. The main element found in the dendrites on the SAC 0307 on PCBs was Tin as it is more mobile than Cu.