Osvaldo Bazzan Kaizer

Tensile bond strength of glass fiber posts luted with different cements

Proper selection of the luting agent is fundamental to avoid failure due to lack of retention in post-retained crowns. The objective of this study was to investigate the tensile bond strength and failure mode of glass fiber posts luted with different cements. Glass fiber posts were luted in 40 mandibular premolars, divided into 4 groups (n = 10): Group 1--resin-modified glass ionomer RelyX Luting; Group 2--resin-modified glass ionomer Fuji Plus; Group 3--resin cement RelyX ARC; Group 4--resin cement Enforce. Specimens were assessed by tensile strength testing and light microscopy analysis for observation of failure mode. The tensile bond strength values of each group were compared by ANOVA and Tukey test. The significance level was set at 5%. The failure modes were described as percentages. The following tensile strength values were obtained: Group 1--247.6 N; Group 2--256.7 N; Group 3--502.1 N; Group 4--477.3 N. There was no statistically significant difference between Groups 1 and 2 or between Groups 3 and 4, yet the resin cements presented significantly higher tensile bond strength values than those presented by the glass ionomer cements. Group 1 displayed 70% of cohesive failures, whereas Groups 2, 3 and 4 exhibited 70% to 80% of adhesive failures at the dentin-cement interface. We concluded that resin cements and glass ionomer cements are able to provide clinically sufficient retention of glass fiber posts, and that glass ionomer cements may be especially indicated when the application of adhesive techniques is difficult.

Prevalence of sleep bruxism in children: A systematic review

INTRODUCTION: Prevalence of sleep bruxism (SB) in children is subject to discussions in the literature. OBJECTIVE: This study is a systematic literature review aiming to critically assess the prevalence of SB in children. METHODS: Survey using the following research databases: MEDLINE, Cochrane, EMBASE, PubMed, Lilacs and BBO, from January 2000 to February 2013, focusing on studies specifically assessing the prevalence of SB in children. RESULTS: After applying the inclusion criteria, four studies were retrieved. Among the selected articles, the prevalence rates of SB ranged from 5.9% to 49.6%, and these variations showed possible associations with the diagnostic criteria used for SB. CONCLUSION: There is a small number of studies with the primary objective of assessing SB in children. Additionally, there was a wide variation in the prevalence of SB in children. Thus, further, evidence-based studies with standardized and validated diagnostic criteria are necessary to assess the prevalence of SB in children more accurately.

Influence of Endodontic Sealer Composition and Time of Fiber Post Cementation on Sealer Adhesiveness to Bovine Root Dentin

This study aimed to assess the influence of the type of endodontic sealer (salicylate resin-based sealer vs. two endodontic sealers) and the time of fiber post cementation after root filling on the post adhesion to bovine root dentin. Sixty bovine roots were assigned to six groups (n=10), considering an experimental design with two factors (factorial 3x2): endodontic sealer factor in three levels [epoxy resin-based sealer (AH Plus), eugenol-based sealer (Endofill), and salicylate resin-based sealer plus mineral trioxide aggregate - MTA (MTA Fillapex)] and time for post cementation factor in two levels (immediate post cementation or 15 days after root canal filling). After post cementation, 2-mm-thick slices were produced and submitted to push-out test. The failure modes were analyzed under a 40× stereomicroscope and scored as: adhesive at cement/dentin interface; adhesive at cement/post interface; cement cohesive; post cohesive; dentin cohesive; or mixed. Data were analyzed using two-way ANOVA and Tukeys post-hoc tests (α=0.05). When the fiber posts were cemented immediately after the root canal filling, the bond strengths were similar, independent of the endodontic sealer type. However, after 15 days, the epoxy resin-based sealer presented higher bond strength than the other sealers (p<0.05). Comparison between each sealer in different experimental times did not reveal any differences. The main failure type was adhesive at dentin/cement interface (89.4%). The time elapsed between the root canal filling and post cementation has no influence on post/root dentin adhesion. On the contrary, the type of endodontic sealer can influence the adhesion between fiber posts and root dentin.

Fatigue surviving, fracture resistance, shear stress and finite element analysis of glass fiber posts with different diameters

This study evaluated the shear stress presented in glass fiber posts with parallel fiber (0°) and different coronal diameters under fatigue, fracture resistance and FEA. 160 glass-fiber posts (N=160) with eight different coronal diameters were used (DT=double tapered, number of the post=coronal diameter and W=Wider - fiber post with coronal diameter wider than the conventional): DT1.4; DT1.8W; DT1.6; DT2W; DT1.8; DT2.2W; DT2; DT2.2. Eighty posts were submitted to mechanical cycling (3×10(6) cycles; inclination: 45°; load: 50N; frequency: 4Hz; temperature: 37°C) to assess the surviving under intermittent loading and other eighty posts were submitted to fracture resistance testing (resistance [N] and shear-stress [MPa] values were obtained). The eight posts types were 3D modeled (Rhinoceros 4.0) and the shear-stress (MPa) evaluated using FEA (Ansys 13.0). One-way ANOVA showed statistically differences to fracture resistance (DT2.2W and DT2.2 showed higher values) and shear stress values (DT1.4 showed lower values). Only the DT1.4 fiber posts failed after mechanical cycling. FEA showed similar values of shear stress between the groups and these values were similar to those obtained by shear stress testing. The failure analysis showed that 95% of specimens failed by shear. Posts with parallel fiber (0°) may suffer fractures when an oblique shear load is applied on the structure; except the thinner group, greater coronal diameters promoted the same shear stresses.

Influence of periodontal ligament simulation on bond strength and fracture resistance of roots restored with fiber posts

Objective Considering that periodontal ligament simulation may influence the stress distribution over teeth restored with intraradicular retainers, this study aimed to assess the combined effect of mechanical cycling and periodontal ligament simulation on both the bond strength between fiber posts and root dentin and the fracture resistance of teeth restored using glass fiber posts. Material and Methods Ninety roots were randomly distributed into 3 groups (n=10) (C-MC: control; P-MC: polyether; AS-MC: addition silicone) to test bond strength and 6 groups (n=10) (C: control; P: polyether; AS: addition silicone, without mechanical cycling, and C-MC, P-MC and AS-MC with mechanical cycling) to test fracture strength, according to the material used to simulate the periodontal ligament. For the bond strength test, fiber posts were cemented, cores were built, mechanical cycling was applied (2×106 cycles, 88 N, 2.2 Hz, and 45º incline), and the teeth cut into 3 slices (2 mm), which were then subjected to the push-out test at 1 mm/min. For the fracture strength test, fiber posts were cemented, cores were built, and half of the groups received mechanical cycling, followed by the compressive strength (45° to the long axis and 1 mm/min) performed on all groups. Results Periodontal ligament simulation did not affect the bond strength (p=0.244) between post and dentin. Simulation of periodontal ligament (p=0.153) and application of mechanical cycling (p=0.97) did not affect fracture resistance. Conclusions The materials used to simulate the periodontal ligament did not affect fracture or bond strength, therefore periodontal ligament simulation using the tested materials could be considered optional in the conditions of the study.

Fiber-matrix integrity, micromorphology and flexural strength of glass fiber posts: Evaluation of the impact of rotary instruments.

Several rotary instruments have been daily employed on clinic to promote cut aiming to adjust the length of fiber posts to the radicular conduct, but there is no information on the literature about the effects of the different rotary instruments and its impact on the micromorphology of surface and mechanical properties of the glass fiber post. This study aimed the impact of rotary instruments upon fiber-matrix integrity, micromorphology and flexural-strength of glass-fiber posts (GFP). GFP (N=110) were divided into 5 groups: Ctrl: as-received posts, DBc: coarse diamond-bur, DBff: extra-fine diamond-bur, CB: carbide-bur, DD: diamond-disc. Cutting procedures were performed under abundant irrigation. Posts exposed to rotary instruments were then subjected to 2-point inclined loading test (compression 45°) (n=10/group) and 3-point flexural-strength test (n=10/group). Fiber-matrix integrity and micromorphology at the cut surface were analyzed using a SEM (n=2/group). Cutting procedures did not significantly affect the 2-point (51.7±4.3-56.7±5.1 MPa) (p=0.0233) and 3-point flexural-strength (671.5±35.3-709.1±33.1 MPa) (p=0.0968) of the posts (One-way ANOVA and Tukey׳s test). Fiber detachment was observed only at the end point of the cut at the margins of the post. Cut surfaces of the CB group were smoother than those of the other groups. After 3-point flexural strength test, fiber-matrix separation was evident at the tensile side of the post. Rotary instruments tested with simultaneous water-cooling did not affect the resistance of the tested fiber posts but caused disintegration of the fibers from the matrix at the end of the cut, located at the margins.

A systematic review of different substance injection and dry needling for treatment of temporomandibular myofascial pain

Temporomandibular myofascial pain presents a major challenge in the diagnosis of temporomandibular disorders (TMD). Due to the characteristics of this condition, intramuscular injection procedures are often needed for adequate control of symptoms and treatment. Thus, the aim of this systematic review was to evaluate the effectiveness of dry needling and injection with different substances in temporomandibular myofascial pain. Electronic databases PubMed, EMBASE, CENTRAL/Cochrane, Lilacs, Scopus, Web of Science and CAPES Catalog of Dissertations and Theses were searched for randomized clinical trials until January 2018. Manual search was performed in relevant journals and in the references/citations of the included studies. The selection of studies was carried out by two independent reviewers according to eligibility criteria. From 7128 eligible studies, 137 were selected for full-text analysis and 18 were included. Due to the heterogeneity of the primary studies it was not possible to perform a meta-analysis. The narrative analysis of the results showed that most of the studies had methodological limitations and biases that compromised the quality of the findings. Dry needling and local anaesthesic injections seem promising, but there is a need to conduct further randomized clinical trials, with larger samples and longer follow-up times, to evaluate the real effectiveness of the technique and evaluated substances.

Tratamento protético pós-cirúrgico de ameloblastoma de maxila

Despite being a benign tumor, the ameloblastoma is usually highly invasive and its surgical removal may lead to structural losses and also biomechanical difficulties for stabilization of prosthetic devices manufactured at a later stage. In addition to the indication of frequent follow-up, postsurgical treatment of ameloblastoma requires prosthetic treatment. Prosthetic rehabilitation of the patient intends to repair the mutilation of the face and/or adjacent structures (if present), allowing to reestablish their functions and quality of life. The success of prosthetic rehabilitation depends on the proper selection of materials and techniques specific for each particular case. This paper reports the fabrication of an obturator prosthesis indicated to repair an extensive maxillary defect, secondary to resection of an ameloblastoma at this region. Key words: Ameloblastoma. Prosthetic rehabilitation. Odontogenic tumour.