S.H. M Jafri

Conductivity engineering of graphene by defect formation

Transport measurements have revealed several exotic electronic properties of graphene. The possibility to influence the electronic structure and hence control the conductivity by adsorption or doping with adatoms is crucial in view of electronics applications. Here, we show that in contrast to expectation, the conductivity of graphene increases with increasing concentration of vacancy defects, by more than one order of magnitude. We obtain a pronounced enhancement of the conductivity after insertion of defects by both quantum mechanical transport calculations as well as experimental studies of carbon nano-sheets. Our finding is attributed to the defect induced mid-gap states, which create a region exhibiting metallic behaviour around the vacancy defects. The modification of the conductivity of graphene by the implementation of stable defects is crucial for the creation of electronic junctions in graphene-based electronics devices.

Improved gas sensing activity in structurally defected bilayer graphene

Graphene is a two-dimensional material with a capability of gas sensing, which is here shown to be drastically improved by inducing gentle disorder in the lattice. We report that by using a focused ion beam technique, controlled disorder can be introduced into the graphene structure through Ga(+) ion irradiation. This disorder leads to an increase in the electrical response of graphene to NO(2) gas molecules by a factor of three in an ambient environment (air). Ab initio density functional calculations indicate that NO(2) molecules bind strongly to Stone-Wales defects, where they modify electronic states close to the Fermi level, which in turn influence the transport properties. The demonstrated gas sensor, utilizing structurally defected graphene, shows faster response, higher conductivity changes and thus higher sensitivity to NO(2) as compared to pristine graphene.

Assessment of a nanoparticle bridge platform for molecular electronics measurements

A combination of electron beam lithography, photolithography and focused ion beam milling was used to create a nanogap platform, which was bridged by gold nanoparticles in order to make electrical measurements and assess the platform under ambient conditions. Non-functionalized electrodes were tested to determine the intrinsic response of the platform and it was found that creating devices in ambient conditions requires careful cleaning and awareness of the contributions contaminants may make to measurements. The platform was then used to make measurements on octanethiol (OT) and biphenyldithiol (BPDT) molecules by functionalizing the nanoelectrodes with the molecules prior to bridging the nanogap with nanoparticles. Measurements on OT show that it is possible to make measurements on relatively small numbers of molecules, but that a large variation in response can be expected when one of the metal-molecule junctions is physisorbed, which was partially explained by attachment of OT molecules to different sites on the surface of the Au electrode using a density functional theory calculation. On the other hand, when dealing with BPDT, high yields for device creation are very difficult to achieve under ambient conditions. Significant hysteresis in the I-V curves of BPDT was also observed, which was attributed primarily to voltage induced changes at the interface between the molecule and the metal.

Identification of vibrational signatures from short chains of interlinked molecule–nanoparticle junctions obtained by inelastic electron tunnelling spectroscopy

Short chains containing a series of metal-molecule-nanoparticle nanojunctions are a nano-material system with the potential to give electrical signatures close to those from single molecule experiments while enabling us to build portable devices on a chip. Inelastic electron tunnelling spectroscopy (IETS) measurements provide one of the most characteristic electrical signals of single and few molecules. In interlinked molecule-nanoparticle (NP) chains containing typically 5-7 molecules in a chain, the spectrum is expected to be a superposition of the vibrational signatures of individual molecules. We have established a stable and reproducible molecule-AuNP multi-junction by placing a few 1,8-octanedithiol (ODT) molecules onto a versatile and portable nanoparticle-nanoelectrode platform and measured for the first time vibrational molecular signatures at complex and coupled few-molecule-NP junctions. From quantum transport calculations, we model the IETS spectra and identify vibrational modes as well as the number of molecules contributing to the electron transport in the measured spectra.

Nanoparticle Bridges for Studying Electrical Properties of Organic Molecules

The use of single molecules as building blocks for practical electronic devices and sensors has high potential for novel applications due to the versatility of electronic properties of the molecules. Nano-sized molecules offer great potential for further miniaturization of electronic devices. We describe a method where such molecules are used to bridge a nanoparticles-nanoelectrode interface and thus determine the electrical properties of such a junction. We describe in detail the fabrication of the platform, its functionalization with molecules, and the basics of the electrical measurements. This platform has been shown to guide electrical current through a few molecules. The versatility of such nanoparticle-molecule-nanoelectrode heterojunctions makes this platform suitable for both basic molecular electronics measurements and also for molecular sensing devices in biological and medical applications.