Sara Cascone

Modeling the Drug Release from Hydrogel-Based Matrices

In this work the behavior of hydrogel-based matrices, the most widespread systems for oral controlled release of pharmaceuticals, has been mathematically described. In addition, the calculations of the model have been validated against a rich set of experimental data obtained working with tablets made of hydroxypropyl methylcellulose (a hydrogel) and theophylline (a model drug). The model takes into account water uptake, hydrogel swelling, drug release, and polymer erosion. The model was obtained as an improvement of a previous code, describing the diffusion in concentrated systems, and obtaining the erosion front (which is a moving boundary) from the polymer mass balance (in this way, the number of fitting parameters was also reduced by one). The proposed model was found able to describe all the observed phenomena, and then it can be considered a tool with predictive capabilities, useful in design and testing of new dosage systems based on hydrogels.

Mathematical modeling of simultaneous drug release and in vivo absorption.

The attention of this review is focussed on the mathematical modeling of the simultaneous processes of drug release and absorption/distribution/metabolism/elimination (ADME processes) following different administration routes. Among all of them, for their clinical importance, the oral, transdermal and local delivery are considered. The bases of the presented mathematical models are shown after the discussion of the most relevant phenomena characterising the particular administration route considered. Then, model performances are compared to experimental evidences in order to evaluate their reliability and soundness. The most important conclusion of this review is that despite the complexity of the problem involved in the description of the fate of the drugs after their administration, the scientific community is close to the solution as witnessed by the various interesting and promising approaches here presented about the oral, transdermal and local administration routes.

On the Behavior of HPMC/Theophylline Matrices for Controlled Drug Delivery

Design of systems for oral controlled release of drug could take advantages from the knowledge of which phenomena take place. In this work matrices obtained by powders compression (50:50, hydroxypropyl methylcellulose, a swelling hydrogel, and theophylline, a model drug) were immersed in water at 37 degrees C, allowing the water uptake and the drug release by lateral surface, confining the cylindrical matrices between glass slides. The tablets, after given immersion times, were withdrawn, cut in several annuli, and subsequently analyzed for the drug and the water concentration radial profiles. The data confirmed the pseudo-diffusive nature of the process, allowing to give a deep insight into the drug release process from swellable hydrogel matrices. In particular, it was confirmed the presence of nonhomogeneous gel layer, rich in water and poor in drug, with a profile of drug concentration which agrees well with a pseudo-diffusion phenomenon.

Controlled drug release from hydrogel-based matrices: Experiments and modeling

Controlled release by oral administration is mainly achieved by pharmaceuticals based on hydrogels. Once swallowed, a matrix made of hydrogels experiences water up-take, swelling, drug dissolution and diffusion, polymer erosion. The detailed understanding and quantification of such a complex behavior is a mandatory prerequisite to the design of novel pharmaceuticals for controlled oral delivery. In this work, the behavior of hydrogel-based matrices has been investigated by means of several experimental techniques previously pointed out (gravimetric, and based on texture analysis); and then all the observed features were mathematically described using a physical model, defined and recently improved by our research group (based on balance equations, rate equations and swelling predictions). The agreement between the huge set of experimental data and the detailed calculations by the model is good, confirming the validity of both the experimental and the theoretical approaches.

The influence of dissolution conditions on the drug ADME phenomena.

In this work, a review of the apparatuses available to mimic what happens to a drug (or to foodstuffs) once ingested is presented. Similarly, a brief review of the models proposed to simulate the fate of a drug administered to a living body is reported. Then, the release kinetics of extended release of diclofenac from a commercial enteric-coated tablet was determined both in a conventional dissolution tester (USP Apparatus 2, Method A) as well as in an apparatus modified to reproduce a given pH evolution, closer to the real one than the one suggested by USP. The two experimental release profiles were reported and discussed; therefore, they were adopted as input functions for a previously proposed pharmacokinetic model. The obtained evolutions with time of plasma concentration were presented and used to assess the effectiveness of the commercial pharmaceutical products. The importance of a correct in vitro simulation for the design of pharmaceutical dosage systems was thus emphasized.

Measurements of non-uniform water content in hydroxypropyl-methyl-cellulose based matrices via texture analysis

The use of hydrogels in the preparation of controlled release pharmaceutical forms is extensively diffused. The main feature of these polymers is their ability to swell forming a gel layer when they enter in contact with fluids. Once the gel layer is formed, the drug contained in the matrix can easily diffuse ensuring a controlled release from the tablet. Measurement of water content within a hydrating matrix based on hydrogels is a key topic in the study of pharmaceutical solid dosage forms. The aim of this work is to evaluate the water content of swollen matrices composed by HPMC and theophylline both in axial and in radial direction, as a function of time, using a texture analysis. A relationship between water content and slope of the force-penetration curves has been obtained using a simplified system in which the water uptake is allowed only in radial direction, obtaining thus partially hydrated matrices with the water content varying only along the radial direction. Once the relationship has been validated, it has been applied in a more complex system in which the polymer swelling takes place in both axial and radial direction. Thus, using the texture analysis it has been possible to determine the water in each position within the hydrated matrices.

Measurements of water content in hydroxypropyl-methyl-cellulose based hydrogels via texture analysis

In this work, a fast and accurate method to evaluate the water content in a cellulose derivative-based matrix subjected to controlled hydration was proposed and tuned. The method is based on the evaluation of the work of penetration required in the needle compression test. The work of penetration was successfully related to the hydrogel water content, assayed by a gravimetric technique. Moreover, a fitting model was proposed to correlate the two variables (the water content and the work of penetration). The availability of a reliable tool is useful both in the quantification of the water uptake phenomena, both in the management of the testing processes of novel pharmaceutical solid dosage forms.

Microencapsulation effectiveness of small active molecules in biopolymer by ultrasonic atomization technique

A method to produce biopolymeric (alginate) microparticles by ultrasonic assisted atomization, previously developed, has been applied to the production of microparticles loaded with a small active molecule (theophylline). Fine loaded alginate droplets have been cross-linked with divalent ions to produce microparticles. Once produced, the particles have been separated by centrifugation or filtration and then they have been dried. Drug release has been evaluated by dissolution tests, dissolving the dried particles in acidic solution at pH 1 for a given time and then at pH 7 to simulate the stomach and intestinal environment, respectively. The encapsulation efficiency and the drug loading have been investigated and the operating conditions have been changed to clarify the role of the transport phenomena on the overall process. To increase the drug loading, shorter separation time and better network’s structure were identified as the key operating parameters to allow the process to gain interest from a practical point of view.

Hydrophilic drug encapsulation in shell-core microcarriers by two stage polyelectrolyte complexation method.

In this study a protocol exploiting the combination of the ultrasonic atomization and the complexation between polyelectrolytes was developed to efficiently encapsulate a hydrophilic chemotherapeutic agent essentially used in the treatment of colon cancer, 5-fluorouracil, in enteric shell-core alginate-based microcarriers. The atomization assisted by ultrasound allowed to obtain small droplets by supplying low energy and avoiding drug degradation. In particular microcarriers were produced in a home-made apparatus where both the core (composed of alginate, drug, and Pluronic F127) and shell (composed of only alginate) feed were separately sent to the coaxial ultrasonic atomizer where they were nebulized and placed in contact with the complexation bulk. With the aim to obtain microstructured particles of alginate encapsulating 5-fluorouracil, different formulations of the first complexation bulk were tested; at last an emulsion made of a calcium chloride aqueous solution and dichloromethane allowed to reach an encapsulation efficiency of about 50%. This result can be considered very interesting considering that in literature similar techniques gave 5-fluorouracil encapsulation efficiencies of about 10%. Since a single complexation stage was not able to assure microcarriers gastroresistance, the formulation of a second complexation bulk was evaluated. The solution of cationic and pH-insoluble Eudragit® RS 100 in dichloromethane was chosen as bulk of second-stage complexation obtaining good enteric properties of shell-core microcarriers, i.e. a 5-FU cumulative release at pH 1 (simulating gastric pH) lower than 35%. The formation of interpolyelectrolyte complex (IPEC) between countercharged polymers and the chemical stability of 5-FU in microcarriers were confirmed by FTIR analysis, the presence of an amorphous dispersion of 5-FU in prepared microparticles was also confirmed by DSC. Finally, shell-core enteric coated microcarriers encapsulating 5-fluorouracil were used to prepare tablets, which can be potentially used as oral administration dosage systems for their 5-fluorouracil slower release.

Swellable Hydrogel-based Systems for Controlled Drug Delivery

The controlled delivery of drugs can be effectively obtained using systems based on hydrogels. Tablets, to be orally administered, represent the simplest and the most traditional dosage systems based on hydrogel. Their formulation and preparation require to mix and to compress, in proper ratios, various excipients, including a swellable polymer and a drug. Carriers for controlled release systems are usually cross-linked polymers able to form hydrogels that show peculiar release mechanisms, where both diffusion and tablet swelling play important roles. When a dry swellable hydrogel-based matrix is immersed in a physiological fluid, this starts to penetrate inside the polymeric hydrophilic matrix. When a certain solvent concentration is reached, the polymeric chains unfold due to a glass–rubber transition, and a gel-like layer is formed. In the swollen region, the drug molecules can easily diffuse toward the outer dissolution medium, once they are dissolved. The polymer network became extremely hydrated where the swollen matrix is in contact with the outer medium, and processes like chain disentanglement take place, “eroding” the matrix. This chapter is focused on the analysis of the state of the art about the uses of carriers for controlled release systems composed by hydrogel-based matrices. This analysis has been performed studying in deep both the experimental and the modeling techniques which have been investigated over the years to characterize all the phenomena involved during the drug release.