Spencer A. Wells

Effective passivation of exfoliated black phosphorus transistors against ambient degradation.

Unencapsulated, exfoliated black phosphorus (BP) flakes are found to chemically degrade upon exposure to ambient conditions. Atomic force microscopy, electrostatic force microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy are employed to characterize the structure and chemistry of the degradation process, suggesting that O2 saturated H2O irreversibly reacts with BP to form oxidized phosphorus species. This interpretation is further supported by the observation that BP degradation occurs more rapidly on hydrophobic octadecyltrichlorosilane self-assembled monolayers and on H-Si(111) versus hydrophilic SiO2. For unencapsulated BP field-effect transistors, the ambient degradation causes large increases in threshold voltage after 6 h in ambient, followed by a ∼ 10(3) decrease in FET current on/off ratio and mobility after 48 h. Atomic layer deposited AlOx overlayers effectively suppress ambient degradation, allowing encapsulated BP FETs to maintain high on/off ratios of ∼ 10(3) and mobilities of ∼ 100 cm(2) V(-1) s(-1) for over 2 weeks in ambient conditions. This work shows that the ambient degradation of BP can be managed effectively when the flakes are sufficiently passivated. In turn, our strategy for enhancing BP environmental stability will accelerate efforts to implement BP in electronic and optoelectronic applications.

Solvent Exfoliation of Electronic-Grade, Two-Dimensional Black Phosphorus

Solution dispersions of two-dimensional (2D) black phosphorus (BP)--often referred to as phosphorene--are achieved by solvent exfoliation. These pristine, electronic-grade BP dispersions are produced with anhydrous organic solvents in a sealed-tip ultrasonication system, which circumvents BP degradation that would otherwise occur via solvated O2 or H2O. Among conventional solvents, N-methylpyrrolidone (NMP) is found to provide stable, highly concentrated (∼0.4 mg/mL) BP dispersions. Atomic force microscopy, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy show that the structure and chemistry of solvent-exfoliated BP nanosheets are comparable to mechanically exfoliated BP flakes. Additionally, residual NMP from the liquid-phase processing suppresses the rate of BP oxidation in ambient conditions. Solvent-exfoliated BP nanosheet field-effect transistors exhibit ambipolar behavior with current on/off ratios and mobilities up to ∼10(4) and ∼50 cm(2) V(-1) s(-1), respectively. Overall, this study shows that stable, highly concentrated, electronic-grade 2D BP dispersions can be realized by scalable solvent exfoliation, thereby presenting opportunities for large-area, high-performance BP device applications.

Covalent functionalization and passivation of exfoliated black phosphorus via aryl diazonium chemistry

Functionalization of atomically thin nanomaterials enables the tailoring of their chemical, optical and electronic properties. Exfoliated black phosphorus (BP)-a layered two-dimensional semiconductor-exhibits favourable charge-carrier mobility, tunable bandgap and highly anisotropic properties, but it is chemically reactive and degrades rapidly in ambient conditions. Here we show that covalent aryl diazonium functionalization suppresses the chemical degradation of exfoliated BP even after three weeks of ambient exposure. This chemical modification scheme spontaneously forms phosphorus-carbon bonds, has a reaction rate sensitive to the aryl diazonium substituent and alters the electronic properties of exfoliated BP, ultimately yielding a strong, tunable p-type doping that simultaneously improves the field-effect transistor mobility and on/off current ratio. This chemical functionalization pathway controllably modifies the properties of exfoliated BP, and thus improves its prospects for nanoelectronic applications.

Ultrahigh sensitivity and layer-dependent sensing performance of phosphorene-based gas sensors.

Two-dimensional (2D) layered materials have attracted significant attention for device applications because of their unique structures and outstanding properties. Here, a field-effect transistor (FET) sensor device is fabricated based on 2D phosphorene nanosheets (PNSs). The PNS sensor exhibits an ultrahigh sensitivity to NO2 in dry air and the sensitivity is dependent on its thickness. A maximum response is observed for 4.8-nm-thick PNS, with a sensitivity up to 190% at 20 parts per billion (p.p.b.) at room temperature. First-principles calculations combined with the statistical thermodynamics modelling predict that the adsorption density is ∼1015 cm−2 for the 4.8-nm-thick PNS when exposed to 20 p.p.b. NO2 at 300 K. Our sensitivity modelling further suggests that the dependence of sensitivity on the PNS thickness is dictated by the band gap for thinner sheets (<10 nm) and by the effective thickness on gas adsorption for thicker sheets (>10 nm).

Chemically Tailoring Semiconducting Two-Dimensional Transition Metal Dichalcogenides and Black Phosphorus

Two-dimensional (2D) semiconducting transition metal dichalcogenides (TMDCs) and black phosphorus (BP) have beneficial electronic, optical, and physical properties at the few-layer limit. As atomically thin materials, 2D TMDCs and BP are highly sensitive to their environment and chemical modification, resulting in a strong dependence of their properties on substrate effects, intrinsic defects, and extrinsic adsorbates. Furthermore, the integration of 2D semiconductors into electronic and optoelectronic devices introduces unique challenges at metal-semiconductor and dielectric-semiconductor interfaces. Here, we review emerging efforts to understand and exploit chemical effects to influence the properties of 2D TMDCs and BP. In some cases, surface chemistry leads to significant degradation, thus necessitating the development of robust passivation schemes. On the other hand, appropriately designed chemical modification can be used to beneficially tailor electronic properties, such as controlling doping levels and charge carrier concentrations. Overall, chemical methods allow substantial tunability of the properties of 2D TMDCs and BP, thereby enabling significant future opportunities to optimize performance for device applications.

Stable aqueous dispersions of optically and electronically active phosphorene.

Significance Few-layered phosphorene, which is isolated through exfoliation from black phosphorus, has attracted great interest due to its unique electronic and optical properties. Although solution-based exfoliation methods have been developed for black phosphorus, these techniques have thus far used anhydrous organic solvents. This approach minimizes exposure to known oxidizing species, but at the cost of limited exfoliation yield and relatively thick flakes. Here, we overcome these limitations by using stabilizing surfactants in deoxygenated water, which results in phosphorene down to the monolayer limit. The resulting aqueous phosphorene dispersions show layer-dependent photoluminescence and enable high-performance field-effect transistors. Overall, this approach holds promise for the solution-phase production of few-layered phosphorene in emerging large-volume applications including electronics and optoelectronics. Understanding and exploiting the remarkable optical and electronic properties of phosphorene require mass production methods that avoid chemical degradation. Although solution-based strategies have been developed for scalable exfoliation of black phosphorus, these techniques have thus far used anhydrous organic solvents in an effort to minimize exposure to known oxidants, but at the cost of limited exfoliation yield and flake size distribution. Here, we present an alternative phosphorene production method based on surfactant-assisted exfoliation and postprocessing of black phosphorus in deoxygenated water. From comprehensive microscopic and spectroscopic analysis, this approach is shown to yield phosphorene dispersions that are stable, highly concentrated, and comparable to micromechanically exfoliated phosphorene in structure and chemistry. Due to the high exfoliation efficiency of this process, the resulting phosphorene flakes are thinner than anhydrous organic solvent dispersions, thus allowing the observation of layer-dependent photoluminescence down to the monolayer limit. Furthermore, to demonstrate preservation of electronic properties following solution processing, the aqueous-exfoliated phosphorene flakes are used in field-effect transistors with high drive currents and current modulation ratios. Overall, this method enables the isolation and mass production of few-layer phosphorene, which will accelerate ongoing efforts to realize a diverse range of phosphorene-based applications.

Probing Out-of-Plane Charge Transport in Black Phosphorus with Graphene-Contacted Vertical Field-Effect Transistors

Black phosphorus (BP) has recently emerged as a promising narrow band gap layered semiconductor with optoelectronic properties that bridge the gap between semimetallic graphene and wide band gap transition metal dichalcogenides such as MoS2. To date, BP field-effect transistors have utilized a lateral geometry with in-plane transport dominating device characteristics. In contrast, we present here a vertical field-effect transistor geometry based on a graphene/BP van der Waals heterostructure. The resulting device characteristics include high on-state current densities (>1600 A/cm(2)) and current on/off ratios exceeding 800 at low temperature. Two distinct charge transport mechanisms are identified, which are dominant for different regimes of temperature and gate voltage. In particular, the Schottky barrier between graphene and BP determines charge transport at high temperatures and positive gate voltages, whereas tunneling dominates at low temperatures and negative gate voltages. These results elucidate out-of-plane electronic transport in BP and thus have implications for the design and operation of BP-based van der Waals heterostructures.

Scanning Probe Nanopatterning and Layer-by-Layer Thinning of Black Phosphorus

Nanopatterning and layer-by-layer thinning of black phosphorus is demonstrated with conductive atomic-force-microscope anodic oxidation. The liquid-phase patterning byproduct is readily removed by water rinsing. An alternating-current bias enables direct nanopatterning and thinning on insulating substrates such as SiO2 /Si. Field-effect transistors with patterned channels show significant improvements in current modulation by up to a factor of 50.

All-Electrical Determination of Crystal Orientation in Anisotropic Two-Dimensional Materials

The crystal orientation of an exfoliated black phosphorous flake is determined by purely electrical means. A sequence of three resistance measurements on an arbitrarily shaped flake with five contacts determines the three independent components of the anisotropic in-plane resistivity tensor, thereby revealing the crystal axes. The resistivity anisotropy ratio decreases linearly with increasing temperature T and carrier density reaching a maximum ratio of 3.0 at low temperatures and densities, while mobility indicates impurity scattering at low T and acoustic phonon scattering at high T.

Extrinsic polarization-controlled optical anisotropy in plasmon-black phosphorus coupled system

Two-dimensional black phosphorus (BP) has drawn extensive research interest due to its promising anisotropic photonic and electronic properties. Here, we study anisotropic optical absorption and photoresponse of exfoliated BP flakes at visible frequencies. We enhance this intrinsic optical anisotropy in BP flakes by coupling plasmonic rectangular nanopatch arrays that support localized surface plasmon resonances. In particular, by combining extrinsic anisotropic plasmonic nanostructures lithographically aligned with intrinsically anisotropic BP flakes, we demonstrate for the first time a combined anisotropic plasmonic-semiconductor coupling that provides significant control over the polarization-dependent optical properties of the plasmon-BP hybrid material system, enhancing polarization-sensitive responses to a larger degree. This hybrid material system not only unveils the plasmon-enhanced mechanisms in BP, but also provides novel controllable functionalities in optoelectronic device applications involving polarization-sensitive optical and electrical responses.