Joohoon Kang

Solvent Exfoliation of Electronic-Grade, Two-Dimensional Black Phosphorus

Solution dispersions of two-dimensional (2D) black phosphorus (BP)--often referred to as phosphorene--are achieved by solvent exfoliation. These pristine, electronic-grade BP dispersions are produced with anhydrous organic solvents in a sealed-tip ultrasonication system, which circumvents BP degradation that would otherwise occur via solvated O2 or H2O. Among conventional solvents, N-methylpyrrolidone (NMP) is found to provide stable, highly concentrated (∼0.4 mg/mL) BP dispersions. Atomic force microscopy, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy show that the structure and chemistry of solvent-exfoliated BP nanosheets are comparable to mechanically exfoliated BP flakes. Additionally, residual NMP from the liquid-phase processing suppresses the rate of BP oxidation in ambient conditions. Solvent-exfoliated BP nanosheet field-effect transistors exhibit ambipolar behavior with current on/off ratios and mobilities up to ∼10(4) and ∼50 cm(2) V(-1) s(-1), respectively. Overall, this study shows that stable, highly concentrated, electronic-grade 2D BP dispersions can be realized by scalable solvent exfoliation, thereby presenting opportunities for large-area, high-performance BP device applications.

Thickness sorting of two-dimensional transition metal dichalcogenides via copolymer-assisted density gradient ultracentrifugation

Two-dimensional transition metal dichalcogenides have emerged as leading successors to graphene due to their diverse properties, which depend sensitively on sample thickness. Although solution-based exfoliation methods hold promise for scalable production of these materials, existing techniques introduce irreversible structural defects and/or lack sufficient control over the sample thickness. In contrast, previous work on carbon nanotubes and graphene has shown that isopycnic density gradient ultracentrifugation can produce structurally and electronically monodisperse nanomaterial populations. However, this approach cannot be directly applied to transition metal dichalcogenides due to their high intrinsic buoyant densities when encapsulated with ionic small molecule surfactants. Here, we overcome this limitation and thus demonstrate thickness sorting of pristine molybdenum disulfide (MoS2) by employing a block copolymer dispersant composed of a central hydrophobic unit flanked by hydrophilic chains that effectively reduces the overall buoyant density in aqueous solution. The resulting solution-processed monolayer MoS2 samples exhibit strong photoluminescence without further chemical treatment.

Stable aqueous dispersions of optically and electronically active phosphorene.

Significance Few-layered phosphorene, which is isolated through exfoliation from black phosphorus, has attracted great interest due to its unique electronic and optical properties. Although solution-based exfoliation methods have been developed for black phosphorus, these techniques have thus far used anhydrous organic solvents. This approach minimizes exposure to known oxidizing species, but at the cost of limited exfoliation yield and relatively thick flakes. Here, we overcome these limitations by using stabilizing surfactants in deoxygenated water, which results in phosphorene down to the monolayer limit. The resulting aqueous phosphorene dispersions show layer-dependent photoluminescence and enable high-performance field-effect transistors. Overall, this approach holds promise for the solution-phase production of few-layered phosphorene in emerging large-volume applications including electronics and optoelectronics. Understanding and exploiting the remarkable optical and electronic properties of phosphorene require mass production methods that avoid chemical degradation. Although solution-based strategies have been developed for scalable exfoliation of black phosphorus, these techniques have thus far used anhydrous organic solvents in an effort to minimize exposure to known oxidants, but at the cost of limited exfoliation yield and flake size distribution. Here, we present an alternative phosphorene production method based on surfactant-assisted exfoliation and postprocessing of black phosphorus in deoxygenated water. From comprehensive microscopic and spectroscopic analysis, this approach is shown to yield phosphorene dispersions that are stable, highly concentrated, and comparable to micromechanically exfoliated phosphorene in structure and chemistry. Due to the high exfoliation efficiency of this process, the resulting phosphorene flakes are thinner than anhydrous organic solvent dispersions, thus allowing the observation of layer-dependent photoluminescence down to the monolayer limit. Furthermore, to demonstrate preservation of electronic properties following solution processing, the aqueous-exfoliated phosphorene flakes are used in field-effect transistors with high drive currents and current modulation ratios. Overall, this method enables the isolation and mass production of few-layer phosphorene, which will accelerate ongoing efforts to realize a diverse range of phosphorene-based applications.

Solution-Based Processing of Monodisperse Two-Dimensional Nanomaterials

Exfoliation of single-layer graphene from bulk graphite and the subsequent discovery of exotic physics and emergent phenomena in the atomically thin limit has motivated the isolation of other two-dimensional (2D) layered nanomaterials. Early work on isolated 2D nanomaterial flakes has revealed a broad range of unique physical and chemical properties with potential utility in diverse applications. For example, the electronic and optical properties of 2D nanomaterials depend strongly on atomic-scale variations in thickness, enabling enhanced performance in optoelectronic technologies such as light emitters, photodetectors, and photovoltaics. Much of the initial research on 2D nanomaterials has relied on micromechanical exfoliation, which yields high-quality 2D nanomaterial flakes that are suitable for fundamental studies but possesses limited scalability for real-world applications. In an effort to overcome this limitation, solution-processing methods for isolating large quantities of 2D nanomaterials have emerged. Importantly, solution processing results in 2D nanomaterial dispersions that are amenable to roll-to-roll fabrication methods that underlie lost-cost manufacturing of thin-film transistors, transparent conductors, energy storage devices, and solar cells. Despite these advantages, solution-based exfoliation methods typically lack control over the lateral size and thickness of the resulting 2D nanomaterial flakes, resulting in polydisperse dispersions with heterogeneous properties. Therefore, post-exfoliation separation techniques are needed to achieve 2D nanomaterial dispersions with monodispersity in lateral size, thickness, and properties. In this Account, we survey the latest developments in solution-based separation methods that aim to produce monodisperse dispersions and thin films of emerging 2D nanomaterials such as graphene, boron nitride, transition metal dichalcogenides, and black phosphorus. First, we motivate the need for precise thickness control in 2D nanomaterials by reviewing thickness-dependent physical properties. Then we present a succinct survey of solution-based exfoliation methods that yield 2D nanomaterial dispersions in organic solvents and aqueous media. The Account subsequently focuses on separation methods, including a critical analysis of their relative strengths and weaknesses for 2D nanomaterials with different buoyant densities, van der Waals interactions, and chemical reactivities. Specifically, we evaluate sedimentation-based density gradient ultracentrifugation (sDGU) and isopycnic DGU (iDGU) for post-exfoliation 2D nanomaterial dispersion separation. The comparative advantages of sedimentation and isopycnic methods are presented in both aqueous and nonaqueous media for 2D nanomaterials with varying degrees of chemical reactivity. Finally, we survey methods for forming homogeneous thin films from 2D nanomaterial dispersions and emerging technologies that are likely to benefit from these structures. Overall, this Account provides not only an overview of the present state-of-the-art but also a forward-looking vision for the field of solution-processed monodisperse 2D nanomaterials.

Solution-Processed Dielectrics Based on Thickness-Sorted Two-Dimensional Hexagonal Boron Nitride Nanosheets

Gate dielectrics directly affect the mobility, hysteresis, power consumption, and other critical device metrics in high-performance nanoelectronics. With atomically flat and dangling bond-free surfaces, hexagonal boron nitride (h-BN) has emerged as an ideal dielectric for graphene and related two-dimensional semiconductors. While high-quality, atomically thin h-BN has been realized via micromechanical cleavage and chemical vapor deposition, existing liquid exfoliation methods lack sufficient control over h-BN thickness and large-area film quality, thus limiting its use in solution-processed electronics. Here, we employ isopycnic density gradient ultracentrifugation for the preparation of monodisperse, thickness-sorted h-BN inks, which are subsequently layer-by-layer assembled into ultrathin dielectrics with low leakage currents of 3 × 10(-9) A/cm(2) at 2 MV/cm and high capacitances of 245 nF/cm(2). The resulting solution-processed h-BN dielectric films enable the fabrication of graphene field-effect transistors with negligible hysteresis and high mobilities up to 7100 cm(2) V(-1) s(-1) at room temperature. These h-BN inks can also be used as coatings on conventional dielectrics to minimize the effects of underlying traps, resulting in improvements in overall device performance. Overall, this approach for producing and assembling h-BN dielectric inks holds significant promise for translating the superlative performance of two-dimensional heterostructure devices to large-area, solution-processed nanoelectronics.

Layer-by-Layer Sorting of Rhenium Disulfide via High-Density Isopycnic Density Gradient Ultracentrifugation

Isopycnic density gradient ultracentrifugation (iDGU) has been widely applied to sort nanomaterials by their physical and electronic structure. However, the commonly used density-gradient medium iodixanol has a finite maximum buoyant density that prevents the use of iDGU for high-density nanomaterials. Here, we overcome this limit by adding cesium chloride (CsCl) to iodixanol, thus increasing its maximum buoyant density to the point where the high-density two-dimensional nanomaterial rhenium disulfide (ReS2) can be sorted in a layer-by-layer manner with iDGU. The resulting aqueous ReS2 dispersions show photoluminescence at ∼1.5 eV, which is consistent with its direct bandgap semiconductor electronic structure. Furthermore, photocurrent measurements on thin films formed from solution-processed ReS2 show a spectral response that is consistent with optical absorbance and photoluminescence data. In addition to providing a pathway for effective solution processing of ReS2, this work establishes a general methodology for sorting high-density nanomaterials via iDGU.

Toxicological Profiling of Highly Purified Single‐Walled Carbon Nanotubes with Different Lengths in the Rodent Lung and Escherichia Coli

Carbon nanotubes (CNTs) exhibit a number of physicochemical properties that contribute to adverse biological outcomes. However, it is difficult to define the independent contribution of individual properties without purified materials. A library of highly purified single-walled carbon nanotubes (SWCNTs) of different lengths is prepared from the same base material by density gradient ultracentrifugation, designated as short (318 nm), medium (789 nm), and long (1215 nm) SWCNTs. In vitro screening shows length-dependent interleukin-1β (IL-1β) production, in order of long > medium > short. However, there are no differences in transforming growth factor-β1 production in BEAS-2B cells. Oropharyngeal aspiration shows that all the SWCNTs induce profibrogenic effects in mouse lung at 21 d postexposure, but there are no differences between tube lengths. In contrast, these SWCNTs demonstrate length-dependent antibacterial effects on Escherichia coli, with the long SWCNT exerting stronger effects than the medium or short tubes. These effects are reduced by Pluronic F108 coating or supplementing with glucose. The data show length-dependent effects on proinflammatory response in macrophage cell line and antibacterial effects, but not on collagen deposition in the lung. These data demonstrate that over the length scale tested, the biological response to highly purified SWCNTs is dependent on the complexity of the nano/bio interface.

Graphene-enabled and directed nanomaterial placement from solution for large-scale device integration

Directed placement of solution-based nanomaterials at predefined locations with nanoscale precision limits bottom-up integration in semiconductor process technology. We report a method for electric-field-assisted placement of nanomaterials from solution by means of large-scale graphene layers featuring nanoscale deposition sites. The structured graphene layers are prepared via either transfer or synthesis on standard substrates, and then are removed once nanomaterial deposition is completed, yielding material assemblies with nanoscale resolution that cover surface areas >1 mm2. In order to demonstrate the broad applicability, we have assembled representative zero-dimensional, one-dimensional, and two-dimensional semiconductors at predefined substrate locations and integrated them into nanoelectronic devices. Ultimately, this method opens a route to bottom-up integration of nanomaterials for industry-scale applications.The placement of nanomaterials at predefined locations is a key requirement for their integration in nanoelectronic devices. Here, the authors devise a method allowing placement of solution-based nanomaterials by using structured graphene layers as deposition sites with the aid of an electric field.

Silicon-Phosphorene Nanocavity-Enhanced Optical Emission at Telecommunications Wavelengths

Generating and amplifying light in silicon (Si) continues to attract significant attention due to the possibility of integrating optical and electronic components in a single material platform. Unfortunately, silicon is an indirect band gap material and therefore an inefficient emitter of light. With the rise of integrated photonics, the search for silicon-based light sources has evolved from a scientific quest to a major technological bottleneck for scalable, CMOS-compatible, light sources. Recently, emerging two-dimensional materials have opened the prospect of tailoring material properties based on atomic layers. Few-layer phosphorene, which is isolated through exfoliation from black phosphorus (BP), is a great candidate to partner with silicon due to its layer-tunable direct band gap in the near-infrared where silicon is transparent. Here we demonstrate a hybrid silicon optical emitter composed of few-layer phosphorene nanomaterial flakes coupled to silicon photonic crystal resonators. We show single-mode emission in the telecommunications band of 1.55 μm ( Eg = 0.8 eV) under continuous wave optical excitation at room temperature. The solution-processed few-layer BP flakes enable tunable emission across a broad range of wavelengths and the simultaneous creation of multiple devices. Our work highlights the versatility of the Si-BP material platform for creating optically active devices in integrated silicon chips.

Solution-Based Processing of Optoelectronically Active Indium Selenide

Layered indium selenide (InSe) presents unique properties for high-performance electronic and optoelectronic device applications. However, efforts to process InSe using traditional liquid phase exfoliation methods based on surfactant-assisted aqueous dispersions or organic solvents with high boiling points compromise electronic properties due to residual surface contamination and chemical degradation. Here, these limitations are overcome by utilizing a surfactant-free, low boiling point, deoxygenated cosolvent system. The resulting InSe flakes and thin films possess minimal processing residues and are structurally and chemically pristine. When employed in photodetectors, individual InSe nanosheets exhibit a maximum photoresponsivity of ≈5 × 107 A W-1 , which is the highest value of any solution-processed monolithic semiconductor to date. Furthermore, the surfactant-free cosolvent system not only stabilizes InSe dispersions but is also amenable to the assembly of electronically percolating InSe flake arrays without posttreatment, which enables the realization of ultrahigh performance thin-film photodetectors. This surfactant-free, deoxygenated cosolvent approach can be generalized to other layered materials, thereby presenting additional opportunities for solution-processed thin-film electronic and optoelectronic technologies.