V. Avati

First measurement of the total proton-proton cross-section at the LHC energy of \chem{\sqrt{s} = 7\,TeV}

TOTEM has measured the differential cross-section for elastic proton-proton scattering at the LHC energy of analysing data from a short run with dedicated large-β* optics. A single exponential fit with a slope B=(20.1±0.2stat±0.3syst)u2009GeV−2 describes the range of the four-momentum transfer squared |t| from 0.02 to 0.33u2009GeV2. After the extrapolation to |t|=0, a total elastic scattering cross-section of (24.8±0.2stat±1.2syst)u2009mb was obtained. Applying the optical theorem and using the luminosity measurement from CMS, a total proton-proton cross-section of (98.3±0.2stat±2.8syst)u2009mb was deduced which is in good agreement with the expectation from the overall fit of previously measured data over a large range of center-of-mass energies. From the total and elastic pp cross-section measurements, an inelastic pp cross-section of was inferred.

Proton-proton elastic scattering at the LHC energy of \chem{\sqrt{s} = 7\,TeV}

Proton-proton elastic scattering has been measured by the TOTEM experiment at the CERN Large Hadron Collider at √ s = 7 TeV in dedicated runs with the Roman Pot detectors placed as close as seven times the transverse beam size (σbeam) from the outgoing beams. After careful study of the accelerator optics and the detector alignment, |t|, the square of four-momentum transferred in the elastic scattering process, has been determined with an uncertainty of δt = 0.1 GeV p |t|. In this letter, first results of the differential cross-section are presented covering a |t|-range from 0.36 to 2.5 GeV 2 . The differential cross-section in the range 0.36 < |t| < 0.47 GeV 2 is described by an exponential with a slope parameter B =( 23.6 ± 0.5 stat ± 0.4 syst )G eV −2 , followed by a significant diffractive minimum at |t| =( 0.53 ± 0.01 stat ± 0.01 syst )G eV 2 .F or|t|-values larger than ∼ 1. 5G eV 2 , the cross-section exhibits a power law behaviour with an exponent of −7.8 ± 0.3 stat ± 0.1 syst . When compared to predictions based on the different available models, the data show a strong discriminative power despite the small t-range covered. open access Copyright c EPLA, 2011

Evidence for non-exponential elastic proton-proton differential cross-section at low |t| and √ s = 8 TeV by TOTEM

Abstract The TOTEM experiment has made a precise measurement of the elastic proton–proton differential cross-section at the centre-of-mass energy s = 8 TeV based on a high-statistics data sample obtained with the β ⁎ = 90 m optics. Both the statistical and systematic uncertainties remain below 1%, except for the t-independent contribution from the overall normalisation. This unprecedented precision allows to exclude a purely exponential differential cross-section in the range of four-momentum transfer squared 0.027 | t | 0.2 GeV 2 with a significance greater than 7 σ . Two extended parametrisations, with quadratic and cubic polynomials in the exponent, are shown to be well compatible with the data. Using them for the differential cross-section extrapolation to t = 0 , and further applying the optical theorem, yields total cross-section estimates of ( 101.5 ± 2.1 ) mb and ( 101.9 ± 2.1 ) mb , respectively, in agreement with previous TOTEM measurements.

Measurement of the forward charged-particle pseudorapidity density in pp collisions at ?s = 7?TeV with the TOTEM experiment

The TOTEM experiment has measured the charged-particle pseudorapidity density dNch/d? in pp collisions at for 5.3<|?|<6.4 in events with at least one charged particle with transverse momentum above 40?MeV/c in this pseudorapidity range. This extends the analogous measurement performed by the other LHC experiments to the previously unexplored forward ? region. The measurement refers to more than 99% of non-diffractive processes and to single and double diffractive processes with diffractive masses above ~3.4?GeV/c2, corresponding to about 95% of the total inelastic cross-section. The dNch/d? has been found to decrease with |?|, from 3.84 ? 0.01(stat) ? 0.37(syst) at |?|=5.375 to 2.38?0.01(stat)?0.21(syst) at |?|=6.375. Several MC generators have been compared to data; none of them has been found to fully describe the measurement.

Final Size Planar Edgeless Silicon Detectors for the TOTEM Experiment

Abstract The TOTEM experiment will detect leading protons scattered in angles of microradians from the interaction point at the large hadron collider. This will be achieved using detectors with a minimized dead area at the edge. The collaboration has developed an innovative structure at the detector edge reducing the conventional dead width to less than 100xa0μm, still using standard planar fabrication technology. In this new development, the current of the surface is decoupled from the sensitive volume current within a few tens of micrometers. The basic working principle is explained in this paper. Final size detectors have been produced using this approach. The current–voltage and current–temperature characteristics of the detectors were studied and the detectors were successfully tested in a coasting beam experiment.

Performance of the Totem Detectors at the LHC

The TOTEM Experiment is designed to measure the total proton–proton cross-section with the luminosity-independent method and to study elastic and diffractive pp scattering at the LHC. To achieve optimum forward coverage for charged particles emitted by the pp collisions in the interaction point IP5, two tracking telescopes, T1 and T2, are installed on each side of the IP in the pseudorapidity region 3.1≤|η|≤6.5, and special movable beam-pipe insertions — called Roman Pots (RP) — are placed at distances of ±147 m and ±220 m from IP5. This article describes in detail the working of the TOTEM detector to produce physics results in the first three years of operation and data taking at the LHC.

LHC Optics Measurement with Proton Tracks Detected by the Roman Pots of the TOTEM Experiment

Precise knowledge of the beam optics at the LHC is crucial to fulfill the physics goals of the TOTEM experiment, where the kinematics of the scattered protons is reconstructed with near-beam telescopes—so-called Roman pots (RP). Before being detected, the protons’ trajectories are influenced by the magnetic fields of the accelerator lattice. Thus precise understanding of the proton transport is of key importance for the experiment. A novel method of optics evaluation is proposed which exploits kinematical distributions of elastically scattered protons observed in the RPs. Theoretical predictions, as well as Monte Carlo studies, show that the residual uncertainty of the optics estimation method is smaller than .

FELIX: A Full acceptance detector at the LHC: Letter of intent

The FELIX Collaboration proposes the construction of a full acceptance detector for the LHC, to be located at Intersection Region 4, and to be commissioned concurrently with the LHC. The primary mission of FELIX is the study of QCD: to provide comprehensive and definitive observations of a very broad range of strong-interaction processes. This document contains a description of the detector concept including details of the individual detector elements and their performance characteristics, an extensive discussion of the physics menu, and the plans for integration of FELIX into the collider lattice and physical environment.

Diamond detectors for the TOTEM timing upgrade

This paper describes the design and the performance of the timing detector developed by the TOTEM Collaboration for the Roman Pots (RPs) to measure the Time-Of-Flight (TOF) of the protons produced in central diffractive interactions at the LHC. The measurement of the TOF of the protons allows the determination of the longitudinal position of the proton interaction vertex and its association with one of the vertices reconstructed by the CMS detectors. The TOF detector is based on single crystal Chemical Vapor Deposition (scCVD) diamond plates and is designed to measure the protons TOF with about 50 ps time precision. This upgrade to the TOTEM apparatus will be used in the LHC run 2 and will tag the central diffractive events up to an interaction pileup of about 1. A dedicated fast and low noise electronics for the signal amplification has been developed. The digitization of the diamond signal is performed by sampling the waveform. After introducing the physics studies that will most profit from the addition of these new detectors, we discuss in detail the optimization and the performance of the first TOF detector installed in the LHC in November 2015.

The TOTEM experiment at LHC

The TOTEM experiment is dedicated to the measurement of the total proton-proton cross-section with the luminosity-independent method and the study of elastic and diffractive scattering processes. Two tracking telescopes, T1 and T2, integrated in the CMS detector, cover the pseudo-rapidity region between 3.1 and 6.5 on both sides of the interaction point IP5. The Roman Pot (RP) stations are located at distances of ± 147m and ± 220 m with respect to the interaction point to measure the very forward scattered protons at very small angles. During the LHC technical stop in winter 2010/2011, the TOTEM experiment was completed with the installation of the T1 telescope and the RP stations at ± 147 m. In 2011, the LHC machine provided special optics with the large s* = 90 m, allowing TOTEM to measure the elastic scattering differential cross section, down to the four-momentum transfer squared |t| = 2×10−2 GeV2. Using the optical theorem and extrapolation of the differential cross section to t = 0 (optical point), the total p-p cross section at the LHC energy of √v = 7 TeV could be computed for the first time. The status of the experiment, the performance of the detectors with emphasis on the RPs are described and the first physics results are presented.