V.V. Kashikhin

Magnet RaD for the US LHC Accelerator Research Program (LARP)

TUA2OR6 Magnet RD fax: 510-486-5310; e-mail: sagourlay@lbl.gov). G. Ambrosio, N. Andreev, E. Barzi, R. Bossert, V. S. Kashikhin, V. V. Kashikhin, F. Nobrega, I. Novitsky, D. Turrioni, R. Yamada, and A.V. Zlobin are with Fermilab National Accelerator Laboratory, Batavia, IL 3 M. Anerella, A. Ghosh , , R. Gupta, M. Harrison, J. Schmazle, and P. Wanderer are with Brookhaven National Laboratory, Upton, NY.

R&D of Nb/sub 3/Sn accelerator magnets at Fermilab

Fermilab is developing and investigating different high-field magnets (HFM) for present and future accelerators. The HFM R&D program focused on the 10-12 T magnets based on Nb/sub 3/Sn superconductor and explored both basic magnet technologies for brittle superconductors-wind-and-react and react-and-wind. Magnet design studies in support of LHC upgrades and VLHC were conducted. A series of 1-m long cos-theta dipole models based on the wind-and-react technique was fabricated and tested. Three 1-m long flat racetracks and the common coil dipole model, based on a single-layer coil and react-and-wind technique, were also fabricated and tested. Extensive theoretical and experimental studies of electro-magnetic instabilities in Nb/sub 3/Sn strands, cables and magnets were performed and led to a successful 10 T dipole model. This paper presents the details of Fermilabs HFM program, reports its status and major results, and formulates the next steps for the program.

Test Results of the First 3.7 m Long Nb3Sn Quadrupole by LARP and Future Plans

In December 2009 during its first cold test, LQS01, the first Long Nb3Sn Quadrupole made by LARP (LHC Accelerator Research Program, a collaboration of BNL, FNAL, LBNL and SLAC), reached its target field gradient of 200 T/m. This target was set in 2005 by the US Department of Energy, CERN and LARP, as a significant milestone toward the development of Nb3Sn quadrupoles for possible use in LHC luminosity upgrades. LQS01 is a 90 mm aperture, 3.7 m long quadrupole using Nb3Sn coils. The coil layout is equal to the layout used in the LARP Technological Quadrupoles (TQC and TQS models). Pre-stress and support are provided by a segmented aluminum shell pre-loaded using bladders and keys, similarly to the TQS models. After the first test the magnet was disassembled, reassembled with an optimized pre-stress, and reached 222 T/m at 4.5 K. In this paper we present the results of both tests and the next steps of the Long Quadrupole R&D.

Design of a 120 mm Bore 15 T Quadrupole for the LHC Upgrade Phase II

Future upgrades to machines like the Large Hadron Collider (LHC) at CERN will push accelerator magnets beyond 10 T forcing the replacement of NbTi superconductors with advanced superconductors such as Nb3Sn. In support of the LHC Phase-II upgrade, the US LHC Accelerator Research Program (LARP) is developing a large bore (120 mm) Nb3Sn Interaction Region (IR) quadrupole (HQ) capable of reaching 15 T at its conductor limit and gradients of 199 T/m at 4.4 K and 219 T/m at 1.9 K. The 1 m long, two-layer magnet, addresses coil alignment and accelerator quality features while exploring the magnet performance limits in terms of gradient, stress and structure. This paper summarizes and reports on the design, mechanical structure, coil windings, reaction and impregnation processes.

Development and Test of LARP Technological Quadrupole (TQC) Magnet

In support of the development of a large-aperture superconducting quadrupole for the Large Hadron Collider (LHC) luminosity upgrade, two-layer quadrupole models (TQC and TQS) with 90 mm aperture are being constructed at Fermilab and LBNL within the framework of the US LHC Accelerator Research Program (LARP). This paper describes the construction and test of model TQC01. ANSYS calculations of the structure are compared with measurements during construction. Fabrication experience is described and in-process measurements are reported. Test results at 4.5 K are presented, including magnet training, current ramp rate studies and magnet quench current. Results of magnetic measurements at helium temperature are also presented.

Development of TQC01, a 90 mm

As a first step toward the development of a large-aperture Nb3Sn superconducting quadrupole for the Large Hadron Collider (LHC) luminosity upgrade, two-layer technological quadrupole models (TQS01 at LBNL and TQC01 at Fermilab) are being constructed within the framework of the US LHC Accelerator Research Program (LARP). Both models use the same coil design, but have different coil support structures. This paper describes the TQC01 design, fabrication technology and summarizes its main parameters

hboxNb_3hbox Sn

The U.S. LHC Accelerator Research Program (LARP) has started the fabrication of 3.7-m long Nb3Sn quadrupole models. The Long Quadrupoles (LQ) are ldquoProof-of-Principlerdquo magnets which are to demonstrate that Nb3Sn technology is mature for use in high energy particle accelerators. Their design is based on the LARP Technological Quadrupole (TQ) models, developed at FNAL and LBNL, which have design gradients higher than 200 T/m and an aperture of 90 mm. The plans for the LQ R&D and a design update are presented and discussed in this paper. The challenges of fabricating long accelerator-quality Nb3Sn coils are presented together with the solutions adopted for the LQ coils (based on the TQ experience). During the fabrication and inspection of practice coils some problems were found and corrected. The fabrication at BNL and FNAL of the set of coils for the first Long Quadrupole is in progress.

Model Quadrupole for LHC Upgrade Based on SS Collar

In support of the development of a large-aperture Nb3Sn superconducting quadrupole for the Large Hadron Collider luminosity upgrade, two models (TQS and TQC) with a 90-mm aperture are being constructed at LBNL and FNAL within the framework of the US LHC Accelerator Research Program (LARP). These models use two identical Nb3Sn coils but have different coil support structures. This paper describes the fabrication, assembly, cool-down and test of TQS01-a model based on key and bladder technology with supporting iron yoke and an aluminum shell. Comparison of the test measurements with design expectations is also reported.

Development and Coil Fabrication for the LARP 3.7-m Long Nb3Sn Quadrupole

A superconducting current transformer with a maximum DC current of 28 kA has been used for Nb/sub 3/Sn cable testing at self-fields under various experimental conditions. A fast data acquisition system was developed and used for accurate measurements of the secondary current. Test results are shown for thirty cables made of MJR, RRP and PIT strands, along with a description of the SC transformer, sample preparation and test procedure. It was found that premature quenches at currents significantly lower than the expected critical currents at low fields were due to electromagnetic instabilities in the superconductor.

Fabrication and Test of TQS01—A 90 mm

Fermilab is involved in the development of new generation high-field accelerator magnets using state-of-the-art Nb/sub 3/Sn strands produced using different technologies. Two 1-m long models-mirror configuration and dipole magnet-were fabricated recently at Fermilab based on powder-in-tube (PIT) Nb/sub 3/Sn strands with small effective filament size. This paper describes the parameters of superconducting strands and cable, the details of magnet design and fabrication procedure, and reports the results of PIT coil testing.