Xiaojing Ren

Boron removal from aqueous solution by direct contact membrane distillation

The removal of boron from aqueous solution by direct contact membrane distillation (DCMD) was studied with self-prepared polyvinylidene fluoride (PVDF) hollow fiber membranes in the present work. The effect of pH, boron concentration, temperature and salt concentration of the feed solution on the boron rejection was investigated. The experimental results indicated that boron rejection was less dependent on the feed pH and salt concentration. DCMD process had high boron removal efficiency (>99.8%) and the permeate boron was below the maximum permissible level even at feed concentration as high as 750 mg/L. Although the permeate flux was enhanced exponentially with the feed temperature increasing, the influence of feed temperature on the boron rejection could be neglected. Finally, the natural groundwater sample containing 12.7 mg/L of boron was treated by DCMD process. The permeate boron kept below 20 microg/L whether the feed was acidified or not, but pre-acidification was helpful to maintain the permeate flux stability. All the experimental results indicated that DCMD could be efficiently used for boron removal from aqueous solution.

Fabrication of asymmetric poly (m-phenylene isophthalamide) nanofiltration membrane for chromium(VI) removal

The feasibility of employing nanofiltration for the removal of chromium (VI) from wastewater was investigated. Poly (m-phenylene isophthalamide) (PMIA) was used to fabricate asymmetric nanofiltration membrane through the phase-inversion technique. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to characterize the obtained membrane, and the both confirmed a much smoother surface which could reduce membrane fouling. The PMIA membrane showed different rejections to electrolytes in a sequence of Na2SO4 > MgSO4 > NaCl > MgCl2, which was similar to the sequence of the negatively charged nanofiltration membranes. Separation experiments on chromium(VI) solution were conducted at various operating conditions, such as feed concentration, applied pressure and pH. It is concluded that chromium(VI) could be effectively removed from chromium-containing wastewater by the PMIA nanofiltration membranes while maintaining their pollution resistance under alkaline condition.

Desalination of brackish groundwater by direct contact membrane distillation

The direct contact membrane distillation (DCMD) applied for desalination of brackish groundwater with self-made polyvinylidene fluoride (PVDF) membranes was presented in the paper. The PVDF membrane exhibited high rejection of non-volatile inorganic salt solutes and a maximum permeate flux 24.5 kg m(-2) h(-1) was obtained with feed temperature at 70 degrees C. The DCMD experimental results indicated that the feed concentration had no significant influence on the permeate flux and the rejection of solute. When natural groundwater was used directly as the feed, the precipitation of CaCO(3) would be formed and clog the hollow fibre inlets with gradual concentration of the feed, which resulted in a rapid decline of the module efficiency. The negative influence of scaling could be eliminated by acidification of the feed. Finally, a 250 h DCMD continuous desalination experiment of acidified groundwater with the concentration factor at constant 4.0 was carried out. The permeate flux kept stable and the permeate conductivity was less than 7.0 microS cm(-1) during this process. Furthermore, there was no deposit observed on the membrane surface. All of these demonstrated that DCMD could be efficiently used for production of high-quality potable water from brackish groundwater with water recovery as high as 75%.

Preparation of hydrophobic PVDF hollow fiber membranes for desalination through membrane distillation

Fabrication of polyvinylidene fluoride (PVDF) hydrophobic asymmetric hollow fiber membranes was studied by introducing inorganic salt LiCl and water soluble polymer polyethylene glycol (PEG) 1500, using N,N-dimethylacetamide (DMAc) as solvent and tap water as the coagulation medium. The membranes properties also were tested and characterized. It is found that the non-solvent additive can increase membranes porosity, ether LiCl or PEG 1500. Because of the addition of PEG 1500, the PVDF membranes obtained a rough topography on the membrane surface and the contact angle of the PVDF membranes increased to 113.50 degrees compared to 89.82 degrees of the PVDF membranes spun without an additive. During direct contact membrane distillation (DCMD) of 0.6 M sodium chloride solution, the PVDF membranes spun with PEG 1500 as a non-solvent additive achieved higher water permeation flux compared to the membranes spun from PVDF/DMAc and PVDF/DMAC/LiCl dopes, but the latter two membranes exhibited higher salt rejection rate.

Fluoride removal from brackish groundwater by direct contact membrane distillation

The direct contact membrane distillation (DCMD) applied for fluoride removal from brackish groundwater is presented. The self-prepared polyvinylidene fluoride membrane exhibited high rejection of inorganic salt solutes and a maximum permeate flux 35.6 kgm(-2) h(-1) was obtained. The feed concentration had no marked impact on the permeate flux and the rejection of fluoride. The precipitation of CaCO3 would clog the hollow fiber inlets and foul the membrane surface with the increase of concentration factor when natural groundwater was used directly as the feed, which resulted in a rapid decline of the module efficiency. This phenomenon was diminished by acidification of the feed. The experimental results showed that the permeate flux and the quality of obtained distillate kept stable before concentration factor reached 5.0 with the acidified groundwater as feed. The membrane module efficiency began to decline gradually when the feed continued to be concentrated, which can be mainly attributed to the formation of CaF2 deposits on the membrane surface. Finally, a 300 h continuous fluoride removal experiment on acidified groundwater was carried out with concentration factor at 4.0, the permeate flux kept stable and the permeate fluoride was not detected.

Preparation of high concentration polyaluminum chloride with high content of Alb or Alc

A novel membrane distillation concentration method was used to prepare high concentration polyaluminum chloride (PACl) with high content of Alb or Alc. 2.52 mol/L PACl1 with 88% Alb and 2.38 mol/L PACl2 with 61% Alc were successfully prepared. Three coagulants, AlCl3, PACl1 and PACl2 were investigated on their hydrolysis behavior and speciation under different conditions. The effects of pH and dilution ratio on Al species distribution were investigated by ferron assay. Experimental result showed that pH had a significant effect on Al species distribution for the three coagulants. Dilution ratio had little effects on Alb and Alc distribution in whole dilution process except the beginning for PACl1 and PACl2. The results indicated that transformation of Al depends largely on their original composition. AlCl3 was the most unstable coagulant among these three coagulants during hydrolysis process. PACl1 and PACl2 with significant amounts of highly charged and stable polynuclear aluminum hydrolysis products were less affected by the hydrolysis conditions and could maintain high speciation stability under various conditions.