Xijin Hua

The effect of cup inclination and wear on the contact mechanics and cement fixation for ultra high molecular weight polyethylene total hip replacements

The present study aimed to investigate individual and combined influences of the cup inclination and wear on the contact mechanics and fixation of a Charnley hip replacement using finite element method. The effects of cup inclination and penetration on the contact mechanics of articulating bearings as well as the stress within the cement and at the bone-cement interface were examined. The maximum contact pressure and the von Mises stress on the cup were reduced by ~30% and ~20% respectively when even a small penetration occurred. However, no large differences were found between different cup penetration depths with regards to either the contact pressure or the von Mises stress. The von Mises stress at the bone-cement interface was predicted almost unaltered with an increased cup inclination angle to 55° for a cup penetration to 4mm. These predictions suggest that the contact mechanics and the cement stress are insensitive to the cup inclination and wear under these normal conditions investigated, therefore explaining the robustness of the Charnley hip implant. An increase in the cup inclination angle to 65°, coupled with a maximum penetration of 4mm, resulted in a large increase in the maximum von Mises stress at the bone-cement interface.

Contact mechanics of modular metal-on-polyethylene total hip replacement under adverse edge loading conditions.

Edge loading can negatively impact the biomechanics and long-term performance of hip replacements. Although edge loading has been widely investigated for hard-on-hard articulations, limited work has been conducted for hard-on-soft combinations. The aim of the present study was to investigate edge loading and its effect on the contact mechanics of a modular metal-on-polyethylene (MoP) total hip replacement (THR). A three-dimensional finite element model was developed based on a modular MoP bearing. Different cup inclination angles and head lateral microseparation were modelled and their effect on the contact mechanics of the modular MoP hip replacement were examined. The results showed that lateral microseparation caused loading of the head on the rim of the cup, which produced substantial increases in the maximum von Mises stress in the polyethylene liner and the maximum contact pressure on both the articulating surface and backside surface of the liner. Plastic deformation of the liner was observed under both standard conditions and microseparation conditions, however, the maximum equivalent plastic strain in the liner under microseparation conditions of 2000 µm was predicted to be approximately six times that under standard conditions. The study has indicated that correct positioning the components to avoid edge loading is likely to be important clinically even for hard-on-soft bearings for THR.

Biphasic investigation of contact mechanics in natural human hips during activities.

The aim of this study was to determine the cartilage contact mechanics and the associated fluid pressurisation of the hip joint under eight daily activities, using a three-dimensional finite element hip model with biphasic cartilage layers and generic geometries. Loads with spatial and temporal variations were applied over time and the time-dependent performance of the hip cartilage during walking was also evaluated. It was found that the fluid support ratio was over 90% during the majority of the cycles for all the eight activities. A reduced fluid support ratio was observed for the time at which the contact region slid towards the interior edge of the acetabular cartilage, but these occurred when the absolute level of the peak contact stress was minimal. Over 10 cycles of gait, the peak contact stress and peak fluid pressure remained constant, but a faster process of fluid exudation was observed for the interior edge region of the acetabular cartilage. The results demonstrate the excellent function of the hip cartilage within which the solid matrix is prevented from high levels of stress during activities owing to the load shared by fluid pressurisation. The findings are important in gaining a better understanding of the hip function during daily activities, as well as the pathology of hip degeneration and potential for future interventions. They provide a basis for future subject-specific biphasic investigations of hip performance during activities.

Experimental validation of finite element modelling of a modular metal-on-polyethylene total hip replacement

Finite element models are becoming increasingly useful tools to conduct parametric analysis, design optimisation and pre-clinical testing for hip joint replacements. However, the verification of the finite element model is critically important. The purposes of this study were to develop a three-dimensional anatomic finite element model for a modular metal-on-polyethylene total hip replacement for predicting its contact mechanics and to conduct experimental validation for a simple finite element model which was simplified from the anatomic finite element model. An anatomic modular metal-on-polyethylene total hip replacement model (anatomic model) was first developed and then simplified with reasonable accuracy to a simple modular total hip replacement model (simplified model) for validation. The contact areas on the articulating surface of three polyethylene liners of modular metal-on-polyethylene total hip replacement bearings with different clearances were measured experimentally in the Leeds ProSim hip joint simulator under a series of loading conditions and different cup inclination angles. The contact areas predicted from the simplified model were then compared with that measured experimentally under the same conditions. The results showed that the simplification made for the anatomic model did not change the predictions of contact mechanics of the modular metal-on-polyethylene total hip replacement substantially (less than 12% for contact stresses and contact areas). Good agreements of contact areas between the finite element predictions from the simplified model and experimental measurements were obtained, with maximum difference of 14% across all conditions considered. This indicated that the simplification and assumptions made in the anatomic model were reasonable and the finite element predictions from the simplified model were valid.

The contact mechanics and occurrence of edge loading in modular metal-on-polyethylene total hip replacement during daily activities

The occurrence of edge loading in hip joint replacement has been associated with many factors such as prosthetic design, component malposition and activities of daily living. The present study aimed to quantify the occurrence of edge loading/contact at the articulating surface and to evaluate the effect of cup angles and edge loading on the contact mechanics of a modular metal-on-polyethylene (MoP) total hip replacement (THR) during different daily activities. A three-dimensional finite element model was developed based on a modular MoP bearing system. Different cup inclination and anteversion angles were modelled and six daily activities were considered. The results showed that edge loading was predicted during normal walking, ascending and descending stairs activities under steep cup inclination conditions (≥55°) while no edge loading was observed during standing up, sitting down and knee bending activities. The duration of edge loading increased with increased cup inclination angles and was affected by the cup anteversion angles. Edge loading caused elevated contact pressure at the articulating surface and substantially increased equivalent plastic strain of the polyethylene liner. The present study suggested that correct positioning the component to avoid edge loading that may occur during daily activities is important for MoP THR in clinical practice.

Influence of clearance on the time-dependent performance of the hip following hemiarthroplasty: A finite element study with biphasic acetabular cartilage properties

Hip hemiarthroplasty is a common treatment for femoral neck fracture. However, the acetabular cartilage may degenerate after hemiarthroplasty leading to postoperative failure and the need for revision surgery. The clearance between the acetabular cartilage and head of the prosthesis is one of the potential reasons for this failure. In this study, the influence of joint clearance on the biomechanical function of a generic hip model in hemiarthroplasty was investigated using biphasic numerical simulation. Both a prolonged loading period of 4000 s and dynamic gait load of 10 cycles were considered. It was found that a larger clearance led to a higher stress level, a faster reduction in load supported by the fluid and a faster cartilage consolidation process. Additionally, the mechanical performance of the acetabular cartilage in the natural model was similar to that in the hemiarthroplasty model with no clearance but different from the hemiarthroplasty models with clearances of 0.5 mm and larger. The results demonstrated that a larger clearance in hip hemiarthroplasty is more harmful to the acetabular cartilage and prosthesis heads with more available dimensions (i.e. smaller increments in diameter) could be manufactured for surgeons to achieve a lower clearance, and reduced contact stress in hemiarthroplasty surgeries.

The influence of the representation of collagen fibre organisation on the cartilage contact mechanics of the hip joint

The aim of this study was to develop a finite element (FE) hip model with subject-specific geometry and biphasic cartilage properties. Different levels of detail in the representation of fibre reinforcement were considered to evaluate the feasibility to simplify the complex depth-dependent fibre pattern in the native hip joint. A FE model of a cadaveric hip with subject-specific geometry was constructed through micro-computed-tomography (µCT) imaging. The cartilage was assumed to be biphasic and fibre-reinforced with different levels of detail in the fibre representation. Simulations were performed for heel-strike, mid-stance and toe-off during walking and one-leg-stance over 1500 s. It was found that the required level of detail in fibre representation depends on the parameter of interest. The contact stress of the native hip joint could be realistically predicted by simplifying the fibre representation to being orthogonally reinforced across the whole thickness. To predict the fluid pressure, depth-dependent fibre organisation is needed but specific split-line pattern on the surface of cartilage is not necessary. Both depth-dependent and specific surface fibre orientations are required to simulate the strains.

Geometric parameterisation of pelvic bone and cartilage in contact analysis of the natural hip: An initial study

Parameterised finite element models of the human hip have the potential to allow controlled analysis of the effect of individual geometric features on the contact mechanics of the joint. However, the challenge lies in defining a set of parameters which sufficiently capture the joint geometry in order to distinguish between individuals. In this study, a simple set of parameters to describe the geometries of acetabulum and cartilage in the hip were extracted from two segmentation-based models, which were then used to generate the parameterised finite element models for the two subjects. The contact pressure and contact area at the articular surface predicted from the parameterised finite element models were compared with the results from the segmentation-based models. The differences in the predicted results between the parameterised models and segmentation-based models were found to be within 11% across seven activities simulated. In addition, the parameterised models were able to replicate features of the contact pressure/area fluctuations over the loading cycle that differed between the two subjects. These results provide confidence that the parameterised approach could be used to generate representative finite element models of the human hip for contact analysis. Such a method has the potential to be used to systematically evaluate geometric features that can be captured from simple clinical measurements and provide a cost- and time-effective approach for stratification of the acetabular geometries in the patient population.

THE CUP OUTER DIAMETER INFLUENCES THE CEMENT FIXATION OF CHARNLEY TOTAL HIP REPLACEMENT

Clinical studies have shown that under similar conditions, a cup with outer diameter of 43 mm has smaller chance of aseptic loosening with increasing penetration depth compared to that of 40 mm. This is attributed to the lower friction torque with larger outer diameter of the acetabular cup. [Wroblewski, 2009]. However, no quantitative analysis has been conducted and whether other factors, such as the wear at the bearing surfaces or the mechanical actions at the bone-cement interface [Coultrup, 2010], will contribute to it should be recognized.