Xueping Ge

Synthesis and evaluation of novel dental monomer with branched carboxyl acid group

To enhance the water miscibility and increase the mechanical properties of dentin adhesives, a new glycerol-based monomer with vinyl and carboxylic acid, 4-((1,3-bis(methacryloyloxy)propan-2-yl)oxy)-2-methylene-4-oxobutanoic acid (BMPMOB), was synthesized and characterized. Dentin adhesive formulations containing 2-hydroxyethyl methacrylate (HEMA), 2,2-bis[4-(2-hydroxy-3-methacryloxypropoxy) phenyl]propane (BisGMA), and BMPMOB were characterized with regard to real-time photopolymerization behavior, water sorption, dynamic mechanical analysis, and microscale three-dimensional internal morphologies and compared with HEMA/BisGMA controls. The experimental adhesive copolymers showed higher glass transition temperature and rubbery moduli, as well as improved water miscibility compared to the controls. The enhanced properties of the adhesive copolymers indicated that BMPMOB is a promising comonomer for dental restorative materials.

Visible-Light Initiated Free-Radical/Cationic Ring-Opening Hybrid Photopolymerization of Methacrylate/Epoxy: Polymerization Kinetics, Crosslinking Structure, and Dynamic Mechanical Properties

The effects of polymerization kinetics and chemical miscibility on the crosslinking structure and mechanical properties of polymers cured by visible-light initiated free-radical/cationic ring-opening hybrid photopolymerization are determined. A three-component initiator system is used and the monomer system contains methacrylates and epoxides. The photopolymerization kinetics is monitored in situ by Fourier transform infrared-attenuated total reflectance. The crosslinking structure is studied by modulated differential scanning calorimetry and dynamic mechanical analysis. X-ray microcomputed tomography is used to evaluate microphase separation. The mechanical properties of polymers formed by hybrid formed by free-radical polymerization. These investigations mark the first time that the benefits of the chain transfer reaction between epoxy and hydroxyl groups of methacrylate, on the crosslinking network and microphase separation during hybrid visible-light initiated photopolymerization, have been determined.

Synthesis and evaluation of novel siloxane-methacrylate monomers used as dentin adhesives.

OBJECTIVES The objectives of this study were to synthesize two new siloxane-methacrylate (SM) monomers for application in dentin adhesives and to investigate the influence of different functionality of the siloxane-containing monomers on the adhesive photopolymerization, water sorption, and mechanical properties. METHODS Two siloxane-methacrylate monomers (SM1 and SM2) with four and eight methacrylate groups were synthesized. Dentin adhesives containing BisGMA, HEMA and the siloxane-methacrylate monomers were photo-polymerized. The experimental adhesives were compared with the control adhesive (HEMA/BisGMA, 45/55, w/w) and characterized with regard to degree of conversion (DC), water miscibility of the liquid resin, water sorption and dynamic mechanical analysis (DMA). RESULTS The experimental adhesives exhibited improved water miscibility as compared to the control. When cured in the presence of 12 wt% water to simulate the wet environment of the mouth, the SM-containing adhesives showed DC comparable to the control. The experimental adhesives showed higher rubbery modulus than the control under dry conditions. Under wet conditions, the mechanical properties of the formulations containing SM monomer with increased functionality were comparable with the control, even with more water sorption. SIGNIFICANCE The concentration and functionality of the newly synthesized siloxane-methacrylate monomers affected the water miscibility, water sorption and mechanical properties of the adhesives. The experimental adhesives show improved water compatibility compared with the control. The mechanical properties were enhanced with an increase of the functionality of the siloxane-containing monomers. The results provide critical structure/property relationships and important information for future development of durable, versatile siloxane-containing dentin adhesives.

Tris(trimethylsilyl)silane as a co-initiator for dental adhesive: Photo-polymerization kinetics and dynamic mechanical property

OBJECTIVES The purpose of this study was to evaluate the polymerization behavior of a model dentin adhesive with tris(trimethylsilyl)silane (TTMSS) as a co-initiator, and to investigate the polymerization kinetics and mechanical properties of copolymers in dry and wet conditions. METHODS A co-monomer mixture based on HEMA/BisGMA (45/55, w/w) was used as a model dentin adhesive. The photoinitiator system included camphorquinone (CQ) as the photosensitizer and the co-initiator was ethyl-4-(dimethylamino) benzoate (EDMAB) or TTMSS. Iodonium salt, diphenyliodonium hexafluorophosphate (DPIHP) serving as a catalyst, was selectively added into the adhesive formulations. The control and the experimental formulations were characterized with regard to the degree of conversion (DC) and dynamic mechanical properties under dry and wet conditions. RESULTS In two-component photoinitiator system (CQ/TTMSS), with an increase of TTMSS concentration, the polymerization rate and DC of CC double bond increased, and showed a dependence on the irradiation time and curing light intensity. The copolymers that contained the three-component photoinitiator system (CQ/TTMSS/DPIHP) showed similar dynamic mechanical properties, under both dry and wet conditions, to the EDMAB-containing system. SIGNIFICANCE The DC of formulations using TTMSS as co-initiator showed a strong dependence on irradiation time. With the addition of TTMSS, the maximum polymerization rate can be adjusted and the network structure became more homogenous. The results indicated that the TTMSS could be used as a substitute for amine-type co-initiator in visible-light induced free radical polymerization of methacrylate-based dentin adhesives.

Probing the dual function of a novel tertiary amine compound in dentin adhesive formulations

OBJECTIVES A novel tertiary amine compound containing three methacrylate-urethane groups was synthesized for application in dentin adhesives. The synthesis, photopolymerization kinetics, and leaching were examined in an earlier study using this novel compound as the co-initiator (0.5 and 1.75wt% based on the total resin mass). The objective of this work was to investigate the potential of TUMA (8-(2-(((2-(methacryloyloxy)ethyl)carbamoyl)oxy)propyl)-6,10-dimethyl-4,12-dioxo-5,11-dioxa-3,8,13-triazapentadecane-1,15-diyl bis(2-methylacrylate)) to serve simultaneously as a co-initiator and co-monomer (15-45wt% based on the total resin mass) in dentin adhesive formulations. The polymerization kinetics, water sorption and dynamic mechanical properties of these novel formulations were determined. MATERIALS AND METHOD The monomer system contained Bisphenol A glycerolate dimethacrylate (BisGMA), 2-hydroxyethylmethacrylate (HEMA) and TUMA (synthesized in our lab) at the mass ratio of 45/(55-x)/x. Two photoinitiator (PI) systems were compared. One initiator system contains three components: camphorquinone (CQ), diphenyliodonium hexafluorophosphate (DPIHP) and ethyl-4-(dimethylamino) benzoate (EDMAB) and the second initiator system contains CQ and DPIHP. The control adhesive formulations are: C0-3: HEMA/BisGMA 45/55 (w/w) and 3-component PI and C0-2: HEMA/BisGMA 45/55 (w/w) and 2-component PI. These controls were used as a comparison to the experimental adhesive resins (Ex-3 or Ex-2), in which x represents the weight percentage of synthesized co-monomer (TUMA) to replace part of BisGMA. The control and experimental adhesive formulations were photo-polymerized and compared with regard to the degree of conversion (DC), polymerization rate (Rp), water sorption and dynamic mechanical analysis (DMA) under both dry and wet conditions. RESULTS C0-3 and Ex-3 formulations had similar DC, while the DC of Ex-2 formulation was higher than C0-2. The DC was similar when comparing the two- component with the three-component photoinitiator system when TUMA was used at the same concentration. DMA under dry conditions shows higher rubbery storage modulus for all experimental formulations, while storage modulus at rubbery region under wet conditions was decreased as compared with control (C0-3). There was no statistically significant difference for the DMA results under both dry and wet conditions when comparing two- and three-component initiator systems with the same TUMA concentration. SIGNIFICANCE The newly synthesized TUMA could serve simultaneously as a co-monomer and co-initiator in the absence of commercial co-initiator. This study provides information for the future development of new co-monomer/co-initiator for dentin adhesives and dental composites.

Self-strengthening hybrid dental adhesive via visible-light irradiation triple polymerization

A self-strengthening methacrylate-based dental adhesive system was developed by introducing an epoxy cyclohexyl trimethoxysilane (TS) which contains both epoxy and methoxysilyl functional groups. The experimental formulation, HEMA/BisGMA/TS (22.5/27.5/50, wt%), was polymerized by visible-light. Real-time Fourier transform infrared spectroscopy (FTIR) was used to investigate in situ the free radical polymerization of methacrylate, ring-opening cationic polymerization of epoxy, and photoacid-induced sol-gel reactions. Among the three simultaneous reactions, the reaction rate of the free radical polymerization was the highest and the hydrolysis/condensation rate was the lowest. With 40s-irradiation, the degrees of conversion of the double bond and epoxy groups at 600 s were 73.2±1.2%, 87.9±2.4%, respectively. Hydrolysis of the methoxysilyl group was initially <5%, and increased gradually to about 50% after 48 h dark storage. Photoacids generated through the visible-light-induced reaction were effective in catalyzing both epoxy ring-opening polymerization and methoxysilyl sol-gel reaction. The mechanical properties of copolymers made with TS concentrations from 5 to 35 wt% were obtained using dynamic mechanical analysis (DMA). In wet conditions, the storage moduli at 70 °C and glass transition temperature were significantly higher than that of the control (p<0.05); these properties increased with TS concentration and storage time. The post reaction of hydrolysis/condensation of alkoxysilane could provide persistent strengthening whether in a neutral or acidic environment and these characteristics could lead to enhanced mechanical properties in the oral environment. The cumulative amount of leached species decreased significantly in the TS-containing copolymers. These results provide valuable information for the development of dental adhesives with reduced leaching of methacrylate monomers and enhanced mechanical properties under the wet, oral environment.

Development of methacrylate/silorane hybrid monomer system: Relationship between photopolymerization behavior and dynamic mechanical properties

Resin chemistries for dental composite are evolving as noted by the introduction of silorane-based composites in 2007. This shift in the landscape from methacrylate-based composites has fueled the quest for versatile methacrylate-silorane adhesives. The objective of this study was to evaluate the polymerization behavior and structure/property relationships of methacrylate-silorane hybrid systems. Amine compound ethyl-4-(dimethylamino) benzoate (EDMAB) or silane compound tris(trimethylsilyl) silane (TTMSS) was selected as coinitiators. The mechanical properties of the copolymer were improved significantly at low concentrations (15, 25, or 35 wt %) of silorane when EDMAB was used as coinitiator. The rubbery moduli of these experimental copolymers were increased by up to 260%, compared with that of the control (30.8 ± 1.9 MPa). Visible phase separation appeared in these formulations if the silorane concentrations in the formulations were 50-75 wt %. The use of TTMSS as coinitiator decreased the phase separation, but there was a concomitant decrease in mechanical properties. In the neat methacrylate formulations, the maximum rates of free-radical polymerization with EDMAB or TTMSS were 0.28 or 0.06 s(-1) , respectively. In the neat silorane resin, the maximum rates of cationic ring-opening polymerization with EDMAB or TTMSS were 0.056 or 0.087 s(-1) , respectively. The phase separation phenomenon may be attributed to differences in the rates of free-radical polymerization of methacrylates and cationic ring-opening polymerization of silorane. In the hybrid systems, free-radical polymerization initiated with EDMAB led to higher crosslink density and better mechanical properties under dry/wet conditions. These beneficial effects were, however, associated with an increase in heterogeneity in the network structure.

Compositional design and optimization of dentin adhesive with neutralization capability

OBJECTIVES The objective of this work was to investigate the polymerization behavior, neutralization capability, and mechanical properties of dentin adhesive formulations with the addition of the tertiary amine co-monomer, 2-N-morpholinoethyl methacrylate (MEMA). METHODS A co-monomer mixture based on HEMA/BisGMA (45/55, w/w) was used as a control adhesive. Compared with the control formulation, the MEMA-containing adhesive formulations were characterized comprehensively with regard to water miscibility of liquid resin, water sorption and solubility of cured polymer, real-time photopolymerization kinetics, dynamic mechanical analysis (DMA), and modulated differential scanning calorimetry (MDSC). The neutralization capacity was characterized by monitoring the pH shift of 1mM lactic acid (LA) solution, in which the adhesive polymers were soaked. RESULTS With increasing MEMA concentrations, experimental copolymers showed higher water sorption, lower glass transition temperature and lower crosslinking density compared to the control. The pH values of LA solution gradually increased from 3.5 to about 6.0-6.5 after 90 days. With the increase in crosslinking density of the copolymers, the neutralization rate was depressed. The optimal MEMA concentration was between 20 and 40 wt%. CONCLUSIONS As compared to the control, the results indicated that the MEMA-functionalized copolymer showed neutralization capability. The crosslinking density of the copolymer networks influenced the neutralization rate.

Effect of crosslinking density of polymers and chemical structure of amine-containing monomers on the neutralization capacity of dentin adhesives.

OBJECTIVES Neutralization of the acidic micro-environment at the tooth/material interface is expected to provide enhanced durability for dental composite restorations. The objective of this study is to explore the effect of amine-containing monomer formulations and the crosslinking density of the resultant polymers on the neutralization capacity. MATERIALS AND METHODS The co-monomer system was varied systematically to obtain different proportions of Bisphenol A glycerolate dimethacrylate (BisGMA) and 2-hydroxyethyl methacrylate (HEMA), while maintaining a constant amount of amine-containing methacrylate monomer. A series of amine-containing monomers covering a range of pKa values were examined. Crosslinking density of formed copolymers was controlled by adjusting the weight content of the dimethacrylate monomer BisGMA. Lactic acid (LA) was used as a probe to analyze the effectiveness of the basic polymers to neutralize acid. The neutralization capacity of each amine-containing crosslinked copolymer was characterized by measuring pH as a function of time when the specimens were soaked in 1-mM LA solution, and the results were compared to the control formulations composed solely of BisGMA and HEMA. Polymer surfaces were examined using the methyl orange (MO) assay to quantify the amount of accessible amine groups. RESULTS For each amine-containing crosslinked co-polymer, the neutralization capacity is enhanced by decreasing crosslinking density (e.g., by reducing BisGMA concentration in the formulation). In addition, more amine groups were accessible when crosslinking density was decreased. For different amine-containing polymers with the same BisGMA concentration, the neutralization capacity is higher when the amino monomers with higher pKa values were used in the formulations. SIGNIFICANCE This is the first time that the neutralization capacity based on crosslinked dental polymers has been studied. The information is important for future development of durable dentin adhesives.

Probing the neutralization behavior of zwitterionic monomer-containing dental adhesive

OBJECTIVE To investigate the polymerization kinetics, neutralization behavior, and mechanical properties of amine-functionalized dental adhesive cured in the presence of zwitterionic monomer, methacryloyloxyethyl phosphorylcholine (MPC). METHODS The control adhesive was a mixture based on HEMA/BisGMA/2-N-morpholinoethyl methacrylate (MEMA) (40/30/30, w/w/w). The control and experimental formulations containing MPC were characterized with regard to water miscibility of liquid resins, photopolymerization kinetics, water sorption and solubility, dynamic mechanical properties and leachables from the polymers (aged in ethanol). The neutralization behavior of the adhesives was determined by monitoring the pH of lactic acid (LA) solution. RESULTS The water miscibility decreased with increasing MPC amount. The water sorption of experimental copolymer specimen was greater than the control. The addition of 8wt% water led to improved photo-polymerization efficiency for experimental formulations at MPC of 2.5 and 5wt%, and significant reduction in the cumulative amounts of leached HEMA, BisGMA, and MEMA, i.e. 90, 60 and 50% reduction, respectively. The neutralization rate of MPC-containing adhesive was faster than control. The optimal MPC concentration in the formulations was 5wt%. SIGNIFICANCE Incompatibility between MEMA and MPC led to a decrease in water miscibility of the liquid resins. Water (at 8wt%) in the MPC-containing formulations (2.5-5wt% MPC) led to higher DC, faster RPmax and significant reduction in leached HEMA, BisGMA, and MEMA. The neutralization rate was enhanced with the addition of MPC in the amine-containing formulation. Promoting the neutralization capability of dentin adhesives could play an important role in reducing recurrent decay at the composite/tooth interface.