Young Woo Jo

Probing graphene grain boundaries with optical microscopy

Grain boundaries in graphene are formed by the joining of islands during the initial growth stage, and these boundaries govern transport properties and related device performance. Although information on the atomic rearrangement at graphene grain boundaries can be obtained using transmission electron microscopy and scanning tunnelling microscopy, large-scale information regarding the distribution of graphene grain boundaries is not easily accessible. Here we use optical microscopy to observe the grain boundaries of large-area graphene (grown on copper foil) directly, without transfer of the graphene. This imaging technique was realized by selectively oxidizing the underlying copper foil through graphene grain boundaries functionalized with O and OH radicals generated by ultraviolet irradiation under moisture-rich ambient conditions: selective diffusion of oxygen radicals through OH-functionalized defect sites was demonstrated by density functional calculations. The sheet resistance of large-area graphene decreased as the graphene grain sizes increased, but no strong correlation with the grain size of the copper was revealed, in contrast to a previous report. Furthermore, the influence of graphene grain boundaries on crack propagation (initialized by bending) and termination was clearly visualized using our technique. Our approach can be used as a simple protocol for evaluating the grain boundaries of other two-dimensional layered structures, such as boron nitride and exfoliated clays.

Role of anions in the AuCl3-doping of carbon nanotubes.

The doping/dedoping mechanism of carbon nanotubes (CNTs) with AuCl(3) has been investigated with regard to the roles of cations and anions. Contrary to the general belief that CNTs are p-doped through the reduction of cationic Au(3+) to Au(0), we observed that chlorine anions play a more important role than Au cations in doping. To estimate the effects of Cl and Au on CNTs, the CNT film was dedoped as a function of the annealing temperature (100-700 °C) under an Ar ambient and was confirmed by the sheet resistance change and the presence of a G-band in the Raman spectra. The X-ray photoelectron spectroscopy (XPS) analysis revealed that the doping level of the CNT film was strongly related to the amount of adsorbed chlorine atoms. Annealing at temperatures up to 200 °C did not change the amount of adsorbed Cl atoms on the CNTs, and the CNT film was stable under ambient conditions. Alternatively, Cl atoms started to dissociate from CNTs at 300 °C, and the stability of the film was degraded. Furthermore, the change in the amount of Cl atoms in CNTs was inversely proportional to the change in the sheet resistance. Our observations of the Cl adsorption, either directly or mediated by an Au precursor on the CNT surface, are congruent with the previous theoretical prediction.

Scalable complementary logic gates with chemically doped semiconducting carbon nanotube transistors.

Use of random network carbon nanotube (CNT) transistors and their applications to complementary logic gates have been limited by several factors such as control of CNT density, existence of metallic CNTs producing a poor yield of devices, absence of stable n-dopant and control of precise position of the dopant, and absence of a scalable and cost-effective fabrication process. Here, we report a scalable and cost-effective fabrication of complementary logic gates by precisely positioning an air-stable n-type dopant, viologen, by inkjet printing on a separated semiconducting CNTs network. The obtained CNT transistors showed a high yield of nearly 100% with an on/off ratio of greater than 10(3) in an optimized channel length (∼9 μm). The n-doped semiconducting carbon nanotube transistors showed a nearly symmetric behavior in the on/off current and threshold voltage with p-type transistors. CMOS inverter, NAND, and NOR logic gates were integrated on a HfO2/Si substrate using the n/p transistor arrays. The gain of inverter is extraordinarily high, which is around 45, and NAND and NOR logic gates revealed excellent output on and off voltages. These series of whole processes were conducted under ambient conditions, which can be used for large-area and flexible thin film technology.

Transparent organic p-dopant in carbon nanotubes: bis(trifluoromethanesulfonyl)imide.

We propose bis(trifluoromethanesulfonyl)imide [(CF(3)SO(2))(2)N](-) (TFSI) as a transparent strong electron-withdrawing p-type dopant in carbon nanotubes (CNTs). The conventional p-dopant, AuCl(3), has several drawbacks, such as hygroscopic effect, formation of Au clusters, decrease in transmittance, and high cost in spite of the significant increase in conductivity. TFSI is converted from bis(trifluoromethanesulfonyl)amine (TFSA) by accepting electrons from CNTs, subsequently losing a proton as a characteristic of a Brønsted acid, and has an inductive effect from atoms with high electronegativity, such as halogen, oxygen, and nitrogen. TFSI produced a similar improvement in conductivity to AuCl(3), while maintaining high thermal stability, and no appreciable change in transmittance with no cluster formation. The effectiveness of TFSI was compared with that of other derivatives.

Effect of Plasma–Nitric Acid Treatment on the Electrical Conductivity of Flexible Transparent Conductive Films

A flexible transparent electrically conductive film (FTCF) was formed on a poly(ethylene terephthalate) film by spraying single-walled carbon nanotubes dispersed with sodium dodecyl benzene sulfonate in water and, to improve the electrical conductivity of FTCF, the effect on plasma treatment followed by nitric acid treatment was investigated. The Ar plasma treatment was effective in dissociating the surfactant and removing impurities attached to the surface of the carbon nanotubes (CNTs). Therefore, through a cyclic treatment composed of an Ar plasma treatment and nitric acid treatment, more effective removal of surfactant and impurities attached to the spray-coated CNTs could be obtained than a cyclic treatment without the plasma treatment. With the optimized cyclic treatment, the sheet resistance (Ωs) of the spray-coated CNTs could be decreased up to 45% by removing most of the surfactant and impurities. Using the repeated cyclic treatment, the FTCF having the Ωs of 160 Ω/ at 81.5% optical transmittance at the wavelength of 550 nm could be obtained.