Youngjin Cho

Fluorine-free mixed amphiphilic polymers based on PDMS and PEG side chains for fouling release applications

Fluorine-free mixed amphiphilic block copolymers with mixtures of short side groups of polydimethyl siloxane (PDMS) and polyethylene glycol (PEG) were synthesized and studied for their ability to influence the surface properties and control the adhesion of marine organisms to coated surfaces. The settlement (attachment) and strength of adhesion of two different marine algae, the green seaweed Ulva and the diatom Navicula, were evaluated against the surfaces. It is known that hydrophobic coatings based on polydimethyl siloxane elastomers (PDMSe) are prone to protein adsorption and accumulation of strongly adherent diatom slimes, in contrast to PEG-based hydrophilic surfaces that inhibit protein adsorption and moderate only weak adhesion of diatoms. By incorporating both PDMS and PEG side chains into the polymers, the effect of incorporating both polar and non-polar groups on fouling-release could be studied. The dry surfaces were characterized by X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure spectroscopy (NEXAFS). The ability of these mixed amphiphilic polymers to reconstruct in water was examined using underwater bubble contact angle and dynamic water contact angle experiments. To understand more about surface reconstruction behavior, protein adsorption experiments were carried out with fluorescein isothiocyanate-labeled bovine serum albumin (BSA-FITC) on both dry and pre-soaked surfaces.

Fluorinated Amphiphilic Polymers and Their Blends for Fouling-Release Applications: The Benefits of a Triblock Copolymer Surface

Surface active triblock copolymers (SABC) with mixed polyethylene glycol (PEG) and two different semifluorinated alcohol side chains, one longer than the other, were blended with a soft thermoplastic elastomer (TPE), polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS). The surface composition of these blends was probed by X-ray photoelectron spectroscopy (XPS) and near edge X-ray absorption fine structure (NEXAFS) spectroscopy. The surface reconstruction of the coatings in water was monitored qualitatively by dynamic water contact angles in air as well as air bubble contact angle measurements in water. By blending the SABC with SEBS, we minimize the amount of the SABC used while achieving a surface that is not greatly different in composition from the pure SABC. The 15 wt % blends of the SABC with long fluoroalkyl side chains showed a composition close to that of the pure SABC while the SABC with shorter perfluoroakyl side chains did not. These differences in surface composition were reflected in the fouling-release performance of the blends for the algae, Ulva and Navicula.

Reconstruction of surfaces from mixed hydrocarbon and PEG components in water: responsive surfaces aid fouling release.

Coatings derived from surface active block copolymers (SABCs) having a combination of hydrophobic aliphatic (linear hydrocarbon or propylene oxide-derived groups) and hydrophilic poly(ethlyene glycol) (PEG) side chains have been developed. The coatings demonstrate superior performance against protein adsorption as well as resistance to biofouling, providing an alternative to coatings containing fluorinated side chains as the hydrophobe, thus reducing the potential environmental impact. The surfaces were examined using dynamic water contact angle, captive air-bubble contact angle, atomic force microscopy, X-ray photoelectron spectroscopy, and near-edge X-ray absorption fine structure analysis. The PS(8K)-b-P(E/B)(25K)-b-PI(10K) triblock copolymer precursor (K3) initially dominated the dry surface. In contrast to previous studies with mixed fluorinated/PEG surfaces, these new materials displayed significant surface changes after exposure to water that allowed fouling resistant behavior. PEG groups buried several nanometers below the surface in the dry state were able to occupy the coating surface after placement in water. The resulting surface exhibits a very low contact angle and good antifouling properties that are very different from those of K3. The surfaces are strongly resistant to protein adsorption using bovine serum albumin as a standard protein challenge. Biofouling assays with sporelings of the green alga Ulva and cells of the diatom Navicula showed the level of adhesion was significantly reduced relative to that of a PDMS standard and that of the triblock copolymer precursor of the SABCs.

Preparation and Characterization of Amphiphilic Triblock Terpolymer-Based Nanofibers as Antifouling Biomaterials

Antifouling surfaces are critical for the good performance of functional materials in various applications including water filtration, medical implants, and biosensors. In this study, we synthesized amphiphilic triblock terpolymers (tri-BCPs, coded as KB) and fabricated amphiphilic nanofibers by electrospinning of solutions prepared by mixing the KB with poly(lactic acid) (PLA) polymer. The resulting fibers with amphiphilic polymer groups exhibited superior antifouling performance to the fibers without such groups. The adsorption of bovine serum albumin (BSA) on the amphiphilic fibers was about 10-fold less than that on the control surfaces from PLA and PET fibers. With the increase of the KB content in the amphiphilic fibers, the resistance to adsorption of BSA was increased. BSA was released more easily from the surface of the amphiphilic fibers than from the surface of hydrophobic PLA or PET fibers. We have also investigated the structural conformation of KB in fibers before and after annealing by contact angle measurements, transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), and coarse-grained molecular dynamics (CGMD) simulation to probe the effect of amphiphilic chain conformation on antifouling. The results reveal that the amphiphilic KB was evenly distributed within as-spun hybrid fibers, while migrated toward the core from the fiber surface during thermal treatment, leading to the reduction in antifouling. This suggests that the antifouling effect of the amphiphilic fibers is greatly influenced by the arrangement of amphiphilic groups in the fibers.

Biodegradability, cytotoxicity, and physicochemical treatability of two novel perfluorooctane sulfonate-free photoacid generators.

There is a need for effective, environmentally compatible photoacid generators (PAGs) for application in photolithography for microelectronic device fabrication. Perfluoroalkyl sulfonates (PFAS) used in conventional PAG formulations, such as perfluorooctane sulfonate (PFOS), are under increasing scrutiny due to their widespread environmental distribution and toxicity. Recently, two new PFAS-free, PAG anions with semifluorinated sulfonate anions containing biomolecules (γ-butyrolactone or d-glucose groups) were successfully applied as PAGs. In this study, the biodegradation potential, cytotoxicity, and physicochemical treatability of the new PAG anions was evaluated. PFOS and perfluorobutane sulfonate (PFBS) were used as reference materials in all of the assays. The new PAGs were susceptible to partial degradation by microorganisms in aerobic activated sludge, and these were also readily removed by chemical oxidative treatment with Fenton’s reagent [H2O2/Fe(II)]. In contrast, the compounds were resistant to microbial and chemical attack under reductive conditions as indicated by the low removal efficiencies observed with anaerobic biodegradation assays and chemical assays with zero-valent iron, respectively. The enhanced biodegradation potential and treatability make of the new PAGs attractive materials to resolve current issues related to the lithographic performance and environmental concerns.

Environmentally friendly natural materials-based photoacid generators for next-generation photolithography

We describe the development of new triphenylsulfonium photoacid generators (TPS PAGs) with semifluorinated sulfonate anions containing glucose or other natural product groups, and their successful application to patterning sub-100 nm features using 254 nm and e-beam lithography. The TPS PAGs with functionalized octafluoro-3-oxapentanesulfonate were synthesized efficiently in high purity and high yield by utilizing simple and unique chemistries on 5-iodooctafluoro-3-oxapentanesulfonyl fluoride. The PAGs has been fully evaluated in terms of chemical properties, lithographic performance, environmental friendliness or toxicological impact. The PAGs are non-toxic and it is susceptible to chemical degradation and to microbial attack under aerobic/anaerobic conditions. These new PAGs are very attractive materials for high resolution photoresist applications and they are particularly useful in addressing the environmental concerns caused by PFOS and other perfluoroalkyl surfactants.