Zbigniew Rybak

Influence of Cu–Ti thin film surface properties on antimicrobial activity and viability of living cells

The paper describes properties of thin-film coatings based on copper and titanium. Thin films were prepared by co-sputtering of Cu and Ti targets in argon plasma. Deposited coatings consist of 90at.% of Cu and 10at.% of Ti. Characterization of the film was made on the basis of investigations of microstructure and physicochemical properties of the surface. Methods such as scanning electron microscopy, x-ray microanalysis, x-ray diffraction, x-ray photoelectron spectroscopy, atomic force microscopy, optical profilometry and wettability measurements were used to assess the properties of deposited thin films. An impact of Cu-Ti coating on the growth of selected bacteria and viability of the living cells (line L929, NCTC clone 929) was described in relation to the structure, surface state and wettability of the film. It was found that as-deposited films were amorphous. However, in such surroundings the nanocrystalline grains of 10-15nm and 25-35nm size were present. High surface active area with a roughness of 8.9nm, had an effect on receiving relatively high water contact angle value (74.1°). Such wettability may promote cell adhesion and result in an increase of the probability of copper ion transfer from the film surface into the cell. Thin films revealed bactericidal and fungicidal effects even in short term-contact. High activity of prepared films was directly related to high amount (ca. 51 %) of copper ions at 1+ state as x-ray photoelectron spectroscopy results have shown.

Evaluation of healing processes of intraosseous defects with and without guided bone regeneration and platelet rich plasma. An animal study

BACKGROUNDnIn most cases, the natural healing of intrabony defects only leads to restoration of tissue continuity without differentiation and function. However, repair is not regarded to be an optimal treatment method, as confirmed in many clinical cases. Thus it is important to choose a surgical procedure which makes it possible to achieve restitution ad integrum of the bone structure. The choice of the GBR technique is crucial, in terms of the clinical conditions and limitations resulting from the use of a particular material.nnnOBJECTIVEnThe objective of this study has been the analysis of effectiveness of selected surgical treatment techniques of intrabony defects in rabbits.nnnMATERIALS AND METHODSnResearch was conducted on 36 white rabbits. The operation technique was a criterion of division into 3 groups: BG/BOC (Bio-Oss Collagen(®)+Bio-Gide Perio(®)), BOC/PRP (Bio-Oss Collagen(®)+PRP), C (control group). Qualitative and quantitative histopathological evaluation was carried out after 1, 3, 6 and 12 months.nnnRESULTSnThe highest value of the bone surface area 31.9% (SD 1.8) was achieved in BOC/BG group three months after the implantation, while the lowest was revealed in C - group - 12.5% (SD 1.32) one month following the procedure.nnnCONCLUSIONSnUpon quantitative histological assessment, the bone tissue presented the most intensive osteogenesis within one month from the application of BOC/PRP, whereas this was observed after the application of BOC/BG in later stages. The application of two regenerative methods influenced the rate, quality and overall treatment of intraosseus defects.

Use of primary culture of human fibroblasts in gingiva augmentation procedure

Abstract Background: The aim of this study was to assess gingival aesthetic after usage of an own method of primary culture of human fibroblasts derived from the connective tissue of oral cavity keratinized gingiva on collagenous carrier in gingival augmentation procedures. Materials and methods: Procedures were performed on 10 patients (7 females, 3 males) aged 18–35 years. In total, 34 teeth in the anterior part of the maxilla and the mandible underwent treatment. The protocol consisted of (1) preparing the patient for tissue biopsy, (2) biopsy of keratinized tissue, (3) laboratory tissue culture, (4) application of expanded cells into the recipient site, and (5) post-procedure management. Aesthetic index, pocket depth (PD), and plaque (PI1) and after surgery complications were examined. Results: There was post-procedure aesthetic improvement in all 34 cases compared with the pre-procedure condition (grade 1), and furthermore a significant decrease in PD and PI1 were revealed. Conclusion: Use of own method of primary culture of human fibroblasts on a collagenous carrier for gingival augmentation is an aesthetic method of mucogingival complex repair.

Increase in cyclooxygenase-2 (COX-2) expression in keratinocytes and dermal fibroblasts in photoaged skin.

Interleukins and NFκ‐B are involved in the development of inflammatory reactions. It has been suggested that these proteins are important contributing factors in the process of photoaging of skin. Moreover, interleukins and NFκ‐B are known to be capable of inducing expression of cyclooxygenase 2 (COX‐2). Expression of COX‐2 in various populations of skin cells has not been examined in the specific processes of aging.

Biological Properties of Low-Toxic PLGA and PLGA/PHB Fibrous Nanocomposite Scaffolds for Osseous Tissue Regeneration. Evaluation of Potential Bioactivity

The aim of the study was to evaluate the biocompatibility and bioactivity of two new prototype implants for bone tissue regeneration made from biodegradable fibrous materials. The first is a newly developed poly(l-lactide-co-glycolide), (PLGA), and the second is a blend of PLGA with synthetic poly([R,S]-3-hydroxybutyrate) (PLGA/PHB). The implant prototypes comprise PLGA or PLGA/PHB nonwoven fabrics with designed pore structures to create the best conditions for cell proliferation. The bioactivity of the proposed implants was enhanced by introducing a hydroxyapatite material and a biologically active agent, namely, growth factor IGF1, encapsulated in calcium alginate microspheres. To assess the biocompatibility and bioactivity, allergenic tests and an assessment of the local reaction of bone tissue after implantation were performed. Comparative studies of local tissue response after implantation into trochanters for a period of 12 months were performed on New Zealand rabbits. Based on the results of the in vivo evaluation of the allergenic effects and the local tissue reaction 12 months after implantation, it was concluded that the two implant prototypes, PLGA + IGF1 and PLGA/PHB + IGF1, were characterized by high biocompatibility with the soft and bone tissues of the tested animals.

Cytotoxicity Evaluation of High-Temperature Annealed Nanohydroxyapatite in Contact with Fibroblast Cells

Biomaterials are substances manufactured for medical purposes in direct contact with the tissues of organisms. Prior to their use, they are tested to determine their usefulness and safety of application. Hydroxyapatites are used in medicine as a bony complement because of their similarity to the natural apatite therein. Thanks to their bioactivity, biocompatibility, stability and non-toxicity hydroxyapatite are the most commonly used materials in osteoimplantology. The use of materials at the nanoscale in medicine or biology may carry the risk of undesirable effects. The aim of the study was to evaluate the cytotoxic effect of high-temperature annealed nanohydroxyapatites on the L929 murine fibroblasts. Nanohydroxyapatites in powder form were obtained by the wet chemistry method: in the temperature range of 800–1000 °C and used for the study. Based on performed studies evaluating the morphology and fibroblast viability, it was found that nanohydroxyapatites show no cytotoxic effects on the L929 cell line.

Biological Properties of Low-Toxicity PLGA and PLGA/PHB Fibrous Nanocomposite Implants for Osseous Tissue Regeneration. Part I: Evaluation of Potential Biotoxicity

In response to the demand for new implant materials characterized by high biocompatibility and bioresorption, two prototypes of fibrous nanocomposite implants for osseous tissue regeneration made of a newly developed blend of poly(l-lactide-co-glycolide) (PLGA) and syntheticpoly([R,S]-3-hydroxybutyrate), PLGA/PHB, have been developed and fabricated. Afibre-forming copolymer of glycolide and l-lactide (PLGA) was obtained by a unique method of synthesis carried out in blocksusing Zr(AcAc)4 as an initiator. The prototypes of the implants are composed of three layers of PLGA or PLGA/PHB, nonwoven fabrics with a pore structure designed to provide the best conditions for the cell proliferation. The bioactivity of the proposed implants has been imparted by introducing a hydroxyapatite material and IGF1, a growth factor. The developed prototypes of implants have been subjected to a set of in vitro and in vivobiocompatibility tests: in vitro cytotoxic effect, in vitro genotoxicity and systemic toxicity. Rabbitsshowed no signs of negative reactionafter implantation of the experimental implant prototypes.

Infrared Thermographic Assessment of Cooling Effectiveness in Selected Dental Implant Systems

The excessive temperature fluctuations during dental implant site preparation may affect the process of bone-implant osseointegration. In the presented studies, we aimed to assess the quality of cooling during the use of 3 different dental implant systems (BEGO®, NEO BIOTECH®, and BIOMET 3i®). The swine rib was chosen as a study model. The preparation of dental implant site was performed with the use of 3 different speeds of rotation (800, 1,200, and 1,500u2009rpm) and three types of cooling: with saline solution at room temperature, with saline solution cooled down to 3°C, and without cooling. A statistically significant difference in temperature fluctuations was observed between BEGO and NEO BIOTECH dental systems when cooling with saline solution at 3°C was used (22.3°C versus 21.8°C). In case of all three evaluated dental implant systems, the highest temperature fluctuations occurred when pilot drills were used for implant site preparation. The critical temperature, defined in the available literature, was exceeded only in case of pilot drills (of all 3 systems) used at rotation speed of 1,500u2009rpm without cooling.

Influence of nanocrystalline structure and surface properties of TiO2 thin films on the viability of L929 cells

Abstract In this work the physicochemical and biological properties of nanocrystalline TiO2 thin films were investigated. Thin films were prepared by magnetron sputtering method. Their properties were examined by X-ray diffraction, photoelectron spectroscopy, atomic force microscopy, optical transmission method and optical profiler. Moreover, surface wettability and scratch resistance were determined. It was found that as-deposited coatings were nanocrystalline and had TiO2-anatase structure, built from crystallites in size of 24 nm. The surface of the films was homogenous, composed of closely packed grains and hydrophilic. Due to nanocrystalline structure thin films exhibited good scratch resistance. The results were correlated to the biological activity (in vitro) of thin films. Morphological changes of mouse fibroblasts (L929 cell line) after contact with the surface of TiO2 films were evaluated with the use of a contrast-phase microscope, while their viability was tested by MTT colorimetric assay. The viability of cell line upon contact with the surface of nanocrystalline TiO2 film was comparable to the control sample. L929 cells had homogenous cytoplasm and were forming a confluent monofilm, while lysis and inhibition of cell growth was not observed. Moreover, the viability in contact with surface of examined films was high. This confirms non-cytotoxic effect of TiO2 film surface on mouse fibroblasts.

Biological Dressings Based on Natural Polymers

FIBRES & TEXTILES in Eastern Europe 2016; 24, 6(120): 170-174. DOI: 10.5604/12303666.1221753 170 Biological Dressings Based on Natural Polymers *Magdalena Kucharska 1, Kinga Brzoza-Malczewska 1, Maria Wiśniewska-Wrona 1, Beata Pałys 1, Marcin H. Struszczyk 2, Magdalena Cichecka 2, Bożena Wilbik-Hałgas 2, Ewa Karuga-Kuźniewska 3, Danuta Paluch 3, Zbigniew Rybak 3 Abstract The article presents a method for producing a IV generation hemostatic dressing in the form of powder consisted of fibrous, which ensures a high level of security in application. The dressing material was developed on the basis of natural polymers of the polysaccharide group such as chitosan and calcium sodium alginate in the form of microand nanofibrids. The dressing structure, utility properties and biocompatibility (cytotoxicity, irritation and sensitization) were studied.