A. Iparraguirre

Solid-phase extraction combined with large volume injection-programmable temperature vaporization-gas chromatography-mass spectrometry for the multiresidue determination of priority and emerging organic pollutants in wastewater.

In the present work the simultaneous extraction for the multiresidue determination in wastewater samples of organic compounds such as polychlorinated biphenyls (PCBs), polybrominated biphenyls (PBBs), pesticides, polycyclic aromatic hydrocarbons (PAHs), phthalate esters (PEs), alkylphenols (APs), bisphenol A (BPA) or hormones included in different lists of priority and emerging pollutants because of their action as endocrine disrupting compounds (EDCs) was developed. Different solid phase extraction (SPE) variables such as the nature of the solid phase (Oasis-HLC, C18 and Lichrolut), the sample volume, the addition of MeOH and NaCl, the pH of the water phase and the volume of the eluent solvent were optimized in order to analyze simultaneously the priority and emerging families of pollutants mentioned above. Good recoveries were obtained for Milli-Q water (80-120%), however, since the use of deuterated analogues and dilution of the sample did not correct the matrix effect, additional SPE clean-up step using Florisil® cartridges was necessary to obtain good results for wastewater samples (80-125%). In order to improve the limits of detection (LODs), large volume injection (LVI) using programmable temperature vaporizer (PTV) coupled to gas chromatography-mass spectrometry (GC-MS) was also optimized. Since analytes losses in the case of the most volatile congeners occurred during the derivatization step and no separation of the derivatized and the non-derivatized analytes was possible during SPE elution, two different injections were optimized for each analyte group. LODs were in good agreement with those found in the literature and relative standard deviations (RSDs) were in the 10-25% range for Milli-Q and 12-30% for wastewater samples. The method was finally applied to the determination of target analytes in three different wastewater treatment plants (WWTPs, Bakio, Gernika and Galindo (Spain)) and in one water purification plant (WPP) in Zornotza (Spain).

Matrix effect during the membrane-assisted solvent extraction coupled to liquid chromatography tandem mass spectrometry for the determination of a variety of endocrine disrupting compounds in wastewater

Membrane-assisted solvent extraction (MASE) coupled to liquid chromatography-triple quadrupole mass spectrometry (LC-MS/MS) was studied for the determination of a variety of emerging and priority compounds in wastewater. Among the target analytes studied certain hormones (estrone (E1), 17β-estradiol (E2), androsterone (ADT), 17α-ethynyl estradiol (EE2), diethylstilbestrol (DES), equilin (EQ), testosterone (TT), mestranol (MeEE2), 19-norethisterone (NT), progesterone (PG) and equilenin (EQN)), alkylphenols (APs) (4-tert-octylphenol (4tOP), nonylphenol technical mixture (NPs) and 4n-octylphenol (4nOP)) and BPA were included. The work was primarily focused in the LC-MS/MS detection step, both in terms of variable optimization and with respect to the matrix effect study. Both, electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI) were assessed both in the negative and positive mode, including the optimization of MS/MS operating conditions. The best results were obtained, in most of the cases, for ESI using 0.05% ammonium hydroxide as buffer solution in the mobile phase, composed with methanol and water. Under optimum detection conditions, matrix effect during the detection step was thoroughly studied. Dilution, correction with deuterated analogues and clean-up of the extracts were evaluated for matrix effect correction. Clean-up with Florisil together with correction with deuterated analogues provided the most satisfactory results, with apparent recoveries in the 57-136% range and method detection limits in the low ngL(-1) level for most of the analytes. For further validation of the method, two separated extraction procedures, the above mentioned MASE, and conventional solid phase extraction (SPE) were compared during the analysis of real samples and comparable results were successfully obtained for E1, E2, EE2, DES, NT, TT, EQ, PG, BPA, ADT, 4nOP, 4tOP, NPs and EQN.

Development of stir-bar sorptive extraction–thermal desorption–gas chromatography–mass spectrometry for the analysis of musks in vegetables and amended soils

The aim of this study was to develop a sensitive and environment-friendly method based on stir-bar sorptive extraction (SBSE) followed by thermal desorption-gas chromatography-mass spectrometry (TD-GC-MS) to determine 8 synthetic musks (musk ambrette, musk ketone, celestolide, tonalide, galaxolide, phantolide, traseolide, and cashmeran) in vegetables (lettuce, carrot, and pepper) and amended soil samples. In a first step sorptive extraction was studied both in the headspace (HSSE) and in the immerse mode (SBSE). The best results were obtained in the immersion mode which was further studied. The influence of the main factors: methanol (20%) and NaCl addition (0%), extraction temperature (40°C) and time (180 min), extraction solvent volume (9 mL) and stirring rate (600 rpm) on the efficiency of SBSE was evaluated by means of experimental designs. In the case of TD, desorption time (10 min), desorption temperature (300°C), cryo-focusing temperature (-30°C), vent flow (75 mL/min) and vent pressure (7.2 psi) were studied using both a fractioned factorial design and a central composite design (CCD). The method was validated in terms of apparent recoveries (AR%), method detection limits (MDLs) and precision at two different concentration levels. Although quantification using instrumental calibration rendered odd results in most of the cases, satisfactory recoveries (74-126%) were obtained in the case of matrix-matched calibration approach for all of the analytes and matrices studied at the two concentration levels evaluated. MDLs in the range of 0.01-0.8 ng/g and 0.01-1.1 ng/g were obtained for vegetables and amended soil samples, respectively. RSD values within 1-23% were obtained for all the analytes and matrices. Finally, the method was applied to the determination of musks in vegetable and amended soil samples.

Uptake of perfluorooctanoic acid, perfluorooctane sulfonate and perfluorooctane sulfonamide by carrot and lettuce from compost amended soil.

Sewage sludge, which acts like a sink for many pollutants, including metals, pathogens and organic pollutants, that are not completely removed in waste water treatment plants (WWTPs), is applied as a nutrient rich organic fertilizer in many agricultural applications. In the present work, carrot and lettuce crops were grown in two different compost amended soils fortified with perfluorooctanoic acid (PFOA), perfluorosulfonate acid (PFOS) and perfluorosulfonamide (FOSA) and cultivated in a greenhouse. The plants were harvested and divided into root core, root peel and leaves in the case of carrots and into heart and leaves for lettuces. Concentrations for all the different compartments were determined to assess the bioconcentration factors (BCFs) and the plant distribution of the target analytes. The highest carrot BCFs for PFOA and PFOS were determined in the leaves (0.6-3.4), while lower values were calculated in the core (0.05-0.6) and the peel (0.05-1.9) compartments. However, PFOA was taken up in the translocation stream and accumulated more than PFOS in the edible part of lettuce. FOSA was totally degraded in the presence of carrot; however, a lower FOSA degradation was observed in presence of the lettuce, which was dependent on the total organic carbon (TOC) content of the soil. The higher the TOC value, the higher the FOSA degradation observed. No degradation was observed in the crop absence. In the case of the carrot experiments, different polymeric materials (polyethersulfone, PES, polyoxymethylene, and silicone rod) were tested to predict the concentration in the cultivation media. A high correlation (r(2)>0.63) was observed for the BCFs in the PES and in the carrot core and peel for PFOA and PFOS. It could be, concluded that the PES can be used as a first approach for the determination of the uptake of compounds such as PFOS and PFOA in carrot.

Matrix solid-phase dispersion of polybrominated diphenyl ethers and their hydroxylated and methoxylated analogues in lettuce, carrot and soil ☆

In the present work, a novel analytical method for the simultaneous determination of ten polybrominated diphenyl ethers (PBDEs), eight methoxylated PBDEs (MeO-PBDEs) and seven hydroxylated PBDEs (OH-PBDEs) in soil, lettuce and carrot samples was developed. The procedure was based on matrix solid-phase dispersion (MSPD) followed by gas chromatography coupled to negative chemical ionization-mass spectrometry (GC-NCI-MS). Under optimum conditions, 0.5g of sample (freeze-dried in the case of lettuce and carrot samples) was dispersed with 0.5g of octadecyl-functionalized silica (C18) and 1.75g of acidified silica (10% H2SO4, w/w) was used as clean-up sorbent. A two-step fractionated elution was carried out. First, PBDEs and MeO-PBDEs were eluted in 75:25% (v/v) n-hexane/dichloromethane mixture and, then, the retained OH-PBDEs were eluted in pure dichloromethane. Both extracts were analyzed by GC-NCI-MS separately, in the case of OH-PBDEs after derivatization with N-methyl-N-(trimethylsilyl) trifluoroacetamide. The developed method was validated in terms of accuracy for soil, lettuce and carrot matrices, spiked at two fortification levels (5 and 25ngg(-1)). After correction with the corresponding surrogate, apparent recovery values (defined as the recovery obtained after correction with the corresponding surrogate) were in the 80-129% range. Precision (as relative standard deviation) in the 1-21% range and method detection limits (MDLs) in the 0.003 and 0.3ngg(-1) range for soil and in the 0.003-0.4ngg(-1) range (dry weight) for lettuce and carrot samples were obtained. For PBDEs the method was also validated with a standard reference material (SRM-2585) of house dust. Finally, the method was applied for the determination of target analytes in soil, lettuce and carrot.

Tetraphasic polar organic chemical integrative sampler for the determination of a wide polarity range organic pollutants in water. The use of performance reference compounds and in-situ calibration

In the present work, a homemade polar organic chemical integrative sampler (POCIS) was studied for the determination of 16 target analytes. The suitability of the combination of triphasic mixture (used in so called pesticides-POCIS) and octadecyl-functionalized silica gel (C18) as sorbent for POCIS was evaluated for the determination of alkylphenols (APs), several hormones, bisphenol-A (BPA), synthetic musk fragrances and herbicides such as trifluralin (Tri) and alachlor (Ala). With this purpose, POCIS laboratory calibration study, using a continuous-flow calibration system, was carried out in order to determine the uptake behavior and sampling rate (Rs) values for each target analyte. While the most hydrophobic compounds, (synthetic musk fragrances, some APs and Tri), showed poor linearity and low accumulation, a linear accumulation was observed for compounds whose logarithmic octanol-water partition coefficient (log Kow) ranged from 5.3 (4-tert-octylphenol, 4t-OP) to 3.1 (cis-androsterone, ADT). The Rs values obtained ranged from 0.190Lday-1 (4t-OP) to 0.042Lday-1 (BPA and equilin, EQ). The addition of C18 to the commonly used triphasic mixture increased the applicability of the POCIS sampler to compounds slightly more non-polar, such as 4t-OP. As far as we know, this is the first time that a combination of tetraphasic sorbent composed by the commercially available triphasic sorbent (Isolute ENV+polystyrene divinylbenzene and Ambersorb 1500 carbon dispersed on S-X3 Biobeads) and C18 was evaluated for passive sampling of the target analytes. The developed POCIS samplers were applied in field experiments from Halle (Germany) wastewater treatment plant (WWTP) effluent. Concerning the calculation of Rs values, the time weighted average (TWA) water concentration CWTWA values were determined considering three different approaches: (i) Rs from laboratory calibration (ii) Rs from laboratory calibration corrected with the use of performance reference compounds (PRCs) and (iii) Rs derived from field experiments or in-situ calibration. Several deuterated compounds such as, [2H3]-17β-estradiol ([2H3]-E2), [2H4]-nonylphenol ([2H4]-NP), [2H4]-equilin ([2H4]-EQ), [2H3]-tonalide ([2H3]-AHTN) and [2H15]-musk xylene ([2H15]-MX) were also studied for their applicability as PRCs. Finally, a reasonable agreement between grab sampling and CWTWA was found when results from in-situ calibration were considered, but not when PRCs were used for correction.

Enrichment of perfluorinated alkyl substances on polyethersulfone using 1-methylpyperidine as ion-pair reagent for the clean-up of carrot and amended soil extracts.

The development of a simple, cheap and environment friendly analytical method for the simultaneous determination of different perfluoroalkyl substances (PFASs) including seven perfluoroalkyl carboxylic acids, three perfluoroalkane sulfonic acids and perfluorooctanesulfonamide in carrot and amended soil was carried out in the present work. The method was based on focused ultrasound solid-liquid extraction followed by extract clean-up through enrichment of the target compounds on a polymeric material using an ion-pair reagent and detection by liquid chromatography-tandem mass spectrometry. The following variables affecting the clean-up step were evaluated: the nature of the polymeric material (polyethersulfone, PES, versus silicone rod), the amount of the polymeric material (from 1 to 9 mg), the ion-pair reagent (1-methylpyperidine, 1-MP, versus tetrabutylammonium salts), the concentration of the ion-pair reagent (from 5 to 50 mM) and the extraction time (from 15 min to 24 h). Optimum clean-up conditions were obtained using preconcentration on 9 mg of PES polymeric material combined with 5 mM 1-MP as ion-pair reagent for 3h. The method was validated in terms of apparent recoveries in the range of 77-140% and 95-137% at the low concentration (50 ng g(-1)) and in the range of 70-136% and 79-132% at the high concentration (290 ng g(-1)) for amended soil and carrot, respectively, after correction with the corresponding labeled standards. Precision, as relative standard deviation, was within 2-23%, while method detection limits were 0.31-2.85 ng g(-1) for amended soil and 0.11-1.83 ng g(-1) for carrot. In the absence of a certified reference material for the target analytes in the matrices studied, inter-method comparison was carried out and the same samples were processed using two independent clean-up procedures, the one developed in the present work and a classical based on solid-phase extraction. Statistically comparable results were obtained according to the one-way analysis of variance for peel, core, leaves as well as amended soil (F(Calc)=2.59, 5.06, 5.82 and 2.34 <F(Crit)=7.71). Finally, the method was applied for the determination of PFASs in uptake experiments where carrots were cultivated in an amended soil polluted with perfluorooctane sulfonic acid (PFOS) at 500 ng g(-1) level. The highest concentration was measured in the carrot leaves (669 ng g(-1)), while the concentrations in peel and core were at the same level (72 ng g(-1) and 62 ng g(-1) respectively), concluding that translocation of PFOS from the soil to the leaves had occurred.