Andre Labonte

EUV patterning successes and frontiers

The feature scaling and patterning control required for the 7nm node has introduced EUV as a candidate lithography technology for enablement. To be established as a front-up lithography solution for those requirements, all the associated aspects with yielding a technology are also in the process of being demonstrated, such as defectivity process window through patterning transfer and electrical yield. This paper will review the current status of those metrics for 7nm at IBM, but also focus on the challenges therein as the industry begins to look beyond 7nm. To address these challenges, some of the fundamental process aspects of holistic EUV patterning are explored and characterized. This includes detailing the contrast entitlement enabled by EUV, and subsequently characterizing state-of-the-art resist printing limits to realize that entitlement. Because of the small features being considered, the limits of film thinness need to be characterized, both for the resist and underlying SiARC or inorganic hardmask, and the subsequent defectivity, both of the native films and after pattern transfer. Also, as we prepare for the next node, multipatterning techniques will be validated in light of the above, in a way that employs the enabling aspects of EUV as well. This will thus demonstrate EUV not just as a technology that can print small features, but one where all aspects of the patterning are understood and enabling of a manufacturing-worthy technology.

TRENCH AND HOLE PATTERNING WITH EUV RESISTS USING DUAL FREQUENCY CAPACITIVELY COUPLED PLASMA (CCP)

Patterning at 10 nm and sub-10 nm technology nodes is one of the key challenges for the semiconductor industry. Several patterning techniques are under investigation to enable the aggressive pitch requirements demanded by the logic technologies. EUV based patterning is being considered as a serious candidate for the sub-10nm nodes. As has been widely published, a new technology like EUV has its share of challenges. One of the main concerns with EUV resists is that it tends to have a lower etch selectivity and worse LER/LWR than traditional 193nm resists. Consequently the characteristics of the dry etching process play an increasingly important role in defining the outcome of the patterning process. In this paper, we will demonstrate the role of the dual-frequency Capacitively Coupled Plasma (CCP) in the EUV patterning process with regards to improving LER/LWR, resist selectivity and CD tunability for holes and line patterns. One of the key knobs utilized here to improve LER and LWR, involves superimposing a negative DC voltage in RF plasma at one of the electrodes. The emission of ballistic electrons, in concert with the plasma chemistry, has shown to improve LER and LWR. Results from this study along with traditional plasma curing methods will be presented. In addition to this challenge, it is important to understand the parameters needed to influence CD tunability and improve resist selectivity. Data will be presented from a systematic study that shows the role of various plasma etch parameters that influence the key patterning metrics of CD, resist selectivity and LER/LWR. This work was performed by the Research Alliance Teams at various IBM Research and Development Facilities.

Plasma etch challenges with new EUV lithography material introduction for patterning for MOL and BEOL

As feature critical dimension (CD) shrinks towards and beyond the 7nm node, patterning techniques for optical lithography with double and triple exposure will be replaced by EUV patterning. EUV enables process and overlay improvement, as well as a potential cost reduction due to fewer wafer passes and masks required for patterning. However, the EUV lithography technique introduces newer types of resists that are thinner and softer compared to conventional 193nm resists currently being used. The main challenge is to find the key etch process parameters to improve the EUV resist selectivity, reduce LER and LWR, minimize line end shrink, improve tip-to-tip degradation, and avoid line wiggling while still enabling previous schemes such as trench-first-metal-hard-mask (TFMHM), self-aligned via (SAV) and self-aligned contact (SAC). In this paper, we will discuss some of the approaches that we have investigated to define the best etch process adjustments to enable EUV patterning. RF pulsing is one of the key parameters utilized to overcome most of the previously described challenges, and has also been coupled with stack optimization. This study will focus on RF pulsing (high vs. low frequency results) and bias control (RF frequency dependence). In particular, pulsing effects on resist morphology, selectivity and profile management will be reported, as well as the role of aspect ratio and etch chemistry on organic mask wiggling and collapse. This work was performed by the Research Alliance Teams at various IBM Research and Development Facilities.

Introduction of pre-etch deposition techniques in EUV patterning

The thin nature of EUV (Extreme Ultraviolet) resist has posed significant challenges for etch processes. In particular, EUV patterning combined with conventional etch approaches suffers from loss of pattern fidelity in the form of line breaks. A typical conventional etch approach prevents the etch process from having sufficient resist margin to control the trench CD (Critical Dimension), minimize the LWR (Line Width Roughness), LER (Line Edge Roughness) and reduce the T2T (Tip-to-Tip). Pre-etch deposition increases the resist budget by adding additional material to the resist layer, thus enabling the etch process to explore a wider set of process parameters to achieve better pattern fidelity. Preliminary tests with pre-etch deposition resulted in blocked isolated trenches. In order to mitigate these effects, a cyclic deposition and etch technique is proposed. With optimization of deposition and etch cycle time as well as total number of cycles, it is possible to open the underlying layers with a beneficial over etch and simultaneously keep the isolated trenches open. This study compares the impact of no pre-etch deposition, one time deposition and cyclic deposition/etch techniques on 4 aspects: resist budget, isolated trench open, LWR/LER and T2T.