GianLuca Sabbi

Design of HQ—A High Field Large Bore

In support of the Large Hadron Collider luminosity upgrade, a large bore (120 mm) Nb3Sn quadrupole with 15 T peak coil field is being developed within the framework of the US LHC Accelerator Research Program (LARP). The 2-layer design with a 15 mm wide cable is aimed at pre-stress control, alignment and field quality while exploring the magnet performance limits in terms of gradient, forces and stresses. In addition, HQ will determine the magnetic, mechanical, and thermal margins of Nb3Sn technology with respect to the requirements of the luminosity upgrade at the LHC.

{\rm Nb}_{3}{\rm Sn}

In support of the development of a large-aperture Nb3Sn superconducting quadrupole for the Large Hadron Collider (LHC) luminosity upgrade, several two-layer technological quadrupole models of TQC series with 90 mm aperture and collar-based mechanical structure have been developed at Fermilab in collaboration with LBNL. This paper summarizes the results of fabrication and test of TQC02a, the second TQC model based on RRP Nb3Sn strand, and TQC02b, built with both MJR and RRP strand. The test results presented include magnet strain and quench performance during training, as well as quench studies of current ramp rate and temperature dependence from 1.9 K to 4.5 K.

Quadrupole Magnet for LARP

Amongst the magnet development program of a large-aperture Nb3Sn superconducting quadrupole for the Large Hadron Collider luminosity upgrade, six quadrupole magnets were built and tested using a shell based key and bladder technology (TQS). The 1 m long 90 mm aperture magnets are part of the US LHC Accelerator Research Program (LARP) aimed at demonstrating Nb3Sn technology by the year 2009, of a 3.6 m long magnet capable of achieving 200 T/m. In support of the LARP program the TQS magnets were tested at three different laboratories, LBNL, FNAL and CERN and while at CERN a technology-transfer and a four days magnet disassembly and reassembly were included. This paper summarizes the fabrication, assembly, cool-down and test results of the six magnets and compares measurements with design expectations.

Fabrication and Test of LARP Technological Quadrupole Models of TQC Series

The U.S. LHC Accelerator Research Program (LARP) has started the fabrication of 3.7-m long Nb3Sn quadrupole models. The Long Quadrupoles (LQ) are ldquoProof-of-Principlerdquo magnets which are to demonstrate that Nb3Sn technology is mature for use in high energy particle accelerators. Their design is based on the LARP Technological Quadrupole (TQ) models, developed at FNAL and LBNL, which have design gradients higher than 200 T/m and an aperture of 90 mm. The plans for the LQ R&D and a design update are presented and discussed in this paper. The challenges of fabricating long accelerator-quality Nb3Sn coils are presented together with the solutions adopted for the LQ coils (based on the TQ experience). During the fabrication and inspection of practice coils some problems were found and corrected. The fabrication at BNL and FNAL of the set of coils for the first Long Quadrupole is in progress.

Test Results of LARP Nb3Sn Quadrupole Magnets Using a Shell-based Support Structure (TQS)

In support of the development of a large-aperture Nb3Sn superconducting quadrupole for the Large Hadron Collider luminosity upgrade, two models (TQS and TQC) with a 90-mm aperture are being constructed at LBNL and FNAL within the framework of the US LHC Accelerator Research Program (LARP). These models use two identical Nb3Sn coils but have different coil support structures. This paper describes the fabrication, assembly, cool-down and test of TQS01-a model based on key and bladder technology with supporting iron yoke and an aluminum shell. Comparison of the test measurements with design expectations is also reported.

Development and Coil Fabrication for the LARP 3.7-m Long Nb3Sn Quadrupole

The 3.7 m long quadrupole magnet LQS01 represents a major step of the US LHC Accelerator Research Program (LARP) towards the development of long Nb3Sn accelerator quadrupole magnets for a LHC Luminosity upgrade. The magnet support structure is a scale up of the 1 m long Technology Quadrupole TQS design with some modifications suggested by TQS model test results. It includes an aluminum shell pre-tensioned over iron yokes using pressurized bladders and locking keys (bladder and key technology). The axial support is provided by two stainless steel end plates compressed against the coil ends by four stainless steel rods. The structure, instrumented with strain gauges, has been fabricated and assembled around four aluminum ldquodummy coilsrdquo to determine pre-load homogeneity and mechanical characteristics during cool-down. After presenting the main magnetic and mechanical parameters of LQS01, we report in this paper on the design, assembly, and test of the support structure, with a comparison between strain gauges data and 3D finite element model results.

Fabrication and Test of TQS01—A 90 mm

The U.S. LHC Accelerator Research Program (LARP), a collaboration between BNL, FNAL, LBNL, and SLAC, has among its major objectives the development of advanced magnet technology for an LHC luminosity upgrade. The LBNL Superconducting Magnet Group supports this program with a broad effort involving design studies, Nb/sub 3/Sn conductor development, mechanical models, and basic prototypes. This paper describes the development of a large aperture Nb/sub 3/Sn racetrack quadrupole magnet using four racetrack coils from the LBNL Subscale Magnet (SM) Program. The magnet provides a gradient of 95 T/m in a 110 mm bore, with a peak field in the conductor of 11.2 T. The coils are pre-stressed by a mechanical structure based on a pre-tensioned aluminum shell, and axially supported with aluminum rods. The mechanical behavior has been monitored with strain gauges and the magnetic field has been measured. Results of the test are reported and analyzed.

{\rm Nb}_{3}{\rm Sn}

Insertion quadrupoles with large bore and high gradient are required to upgrade the luminosity of the large hadron collider (LHC). The US LHC accelerator research program is developing Nb3Sn technology for the upgrade. This effort includes a series of 1 m long technology quadrupoles (TQ), to demonstrate the reproducibility at moderate field, and high-gradient quadrupoles (HQ) to explore the magnet performance limits in terms of peak fields, forces and stresses. The HQ models are expected to achieve peak fields of 15 T or higher. A coil aperture of 90 mm, corresponding to gradients above 300 T/m, was chosen as the baseline. Peak stresses above 150 MPa are expected. Progress on the magnetic and mechanical design of the HQ models will be reported.

Quadrupole Magnet for LARP

We report on the fabrication, assembly, and test of the Nb3Sn dipole magnet HD2. The magnet, aimed at demonstrating the application of Nb3Sn superconductor in high field accelerator-type dipoles, features a 36 mm clear bore surrounded by block-type coils with tilted ends. The coil design is optimized to minimize geometric harmonics in the aperture and the magnetic peak field on the conductor in the coil ends. The target bore field of 15 T at 4.3 K is consistent with critical current measurements of extracted strands. The coils are horizontally pre-stressed during assembly using an external aluminum shell pre-tensioned with water-pressurized bladders. Axial pre-loading of the coil ends is accomplished through two end plates and four aluminum tension rods. The strain in coil, shell, and rods is monitored with strain gauges during assembly, cool-down and magnet excitation, and compared with 3D finite element computations. Magnets training performance, quench locations, and ramp-rate dependence are then analysed and discussed.

Fabrication and Test of a 3.7 m Long Support Structure for the LARP

As part of the LHC Accelerator Research Program (LARP) to build a high performance quadrupole magnet with Nb3Sn conductor, a pair of 3.6 m-long Nb3Sn racetrack coils has been made at Brookhaven National Laboratory (BNL) and installed in two shell-type support structures built by Lawrence Berkeley National Laboratory (LBL). These magnet assemblies have been tested at 4.5 K at BNL to gauge the effect of extended length and prestress on the mechanical performance of the long structure compared to earlier short models. This paper presents the results of quench testing and compares the overall performance of the two versions of the support structure. We also summarize the shell strain measurements and discuss the variation of quench current with ramp rate.