Matthias Kollosche

Soft Conductive Elastomer Materials for Stretchable Electronics and Voltage Controlled Artificial Muscles

Block copolymer elastomer conductors (BEC) are mixtures of block copolymers grafted with conducting polymers, which are found to support very large strains, while retaining a high level of conductivity. These novel materials may find use in stretchable electronics. The use of BEC is demonstrated in a capacitive strain sensor and in an artificial muscle of the dielectric elastomer actuator type, supporting more than 100% actuation strain and capacity strain sensitivity up to 300%.

Elastic block copolymer nanocomposites with controlled interfacial interactions for artificial muscles with direct voltage control

Soft, physically crosslinking, block copolymer elastomers were filled with surface-treated nanoparticles, in order to evaluate the possibility for improvement of their properties when used as soft dielectric actuators. The nanoparticles led to improvements in dielectric properties, however they also reinforced the elastomer matrix. Comparing dielectric spectra of composites with untreated and surface-treated particles showed a measurable influence of the surface on the dielectric loss behaviour for high filler amounts, strongly indicating an improved host–guest interaction for the surface-treated particles. Breakdown strength was measured using a test bench and was found to be in good agreement with the results from the actuation measurements. Actuation responses predicted by a model for prestrained actuators agreed well with measurements up to a filler amount of 20%vol. Strong improvements in actuation behaviour were observed, with an optimum near 15%volnanoparticles, corresponding to a reduction in electrical field of 27% for identical actuation strains. The use of physically crosslinking elastomer ensured the mechanical properties of the matrix elastomer were unchanged by nanoparticles effecting the crosslinking reaction, contrary to similar experiments performed with chemically crosslinking elastomers. This allows for a firm conclusion about the positive effects of surface-treated nanoparticles on actuation behavior.

Dielectric properties and electric breakdown strength of a subpercolative composite of carbon black in thermoplastic copolymer

We investigate the dielectric properties and electric breakdown strength of subpercolative composites of conductive carbon black particles in a rubber insulating matrix. A significant increase in the permittivity in the vicinity of the insulator to conductor transition was observed, with relatively low increases in dielectric loss; however, a rapid decrease in electric breakdown strength was inevitable. A steplike feature was ascribed to agglomeration effects. The low ultimate values of the electric field strength of such composites appear to prohibit practical use.

Standards for dielectric elastomer transducers

Dielectric elastomer transducers consist of thin electrically insulating elastomeric membranes coated on both sides with compliant electrodes. They are a promising electromechanically active polymer technology that may be used for actuators, strain sensors, and electrical generators that harvest mechanical energy. The rapid development of this field calls for the first standards, collecting guidelines on how to assess and compare the performance of materials and devices. This paper addresses this need, presenting standardized methods for material characterisation, device testing and performance measurement. These proposed standards are intended to have a general scope and a broad applicability to different material types and device configurations. Nevertheless, they also intentionally exclude some aspects where knowledge and/or consensus in the literature were deemed to be insufficient. This is a sign of a young and vital field, whose research development is expected to benefit from this effort towards standardisation.

Molecular composites with enhanced energy density for electroactive polymers

Actuators based on soft dielectric elastomers deform due to electric field induced Maxwells stress, interacting with the mechanical properties of the material. The relatively high operating voltages of such actuators can be reduced by increasing the permittivity of the active material, while maintaining the mechanical properties and high electrical breakdown strength. Approaches relying on the use of highly polarizable molecules or conjugated polymers have so far provided the best results, however it has been difficult to maintain high breakdown strengths. In this work, a new approach for increasing the electrostatic energy density of a soft polymer based on molecular composites is presented, relying on chemically grafting soft gel-state π-conjugated conducting macromolecules (polyaniline (PANI)) to a flexible elastomer backbone SEBS-g-MA (poly-styrene-co-ethylene-co-butylene-co-styrene-g-maleic anhydride). The approach was found to result in composites of increased permittivity (470% over the elastomer matrix) with hardly any reduction in breakdown strength (from 140 to 120 V μm−1), resulting in a large increase in stored electrostatic energy. This led to an improvement in the measured electromechanical response as well as in the maximum actuation strain. A transition was observed when amounts of PANI exceeded 2 vol%, which was ascribed to the exhaustion of the MA-functionality of the SEBS-g-MA. The transition led to drastic increases in permittivity and conductivity, and a sharp drop in electrical breakdown strength. Although the transition caused further improvement of the electromechanical response, the reduction in electrical breakdown strength caused a limitation of the maximum achievable actuation strain.

Robust Flexible Capacitive Surface Sensor for Structural Health Monitoring Applications

Early detection of possible defects in civil infrastructure is vital to ensuring timely maintenance and extending structure life expectancy. The authors recently proposed a novel method for structural health monitoring based on soft capacitors. The sensor consisted of an off-the-shelf flexible capacitor that could be easily deployed over large surfaces, the main advantages being cost-effectiveness, easy installation, and allowing simple signal processing. In this paper, a capacitive sensor with tailored mechanical and electrical properties is presented, resulting in greatly improved robustness while retaining measurement sensitivity. The sensor is fabricated from a thermoplastic elastomer mixed with titanium dioxide and sandwiched between conductive composite electrodes. Experimental verifications conducted on wood and concrete specimens demonstrate the improved robustness, as well as the ability of the sensing method to diagnose and locate strain.

Electrical failure in blends of chemically identical, soft thermoplastic elastomers with different elastic stiffness

Investigations on the effect of stiffness on breakdown strength in polymer materials are typically performed indirectly by variation of temperature. Here, the stiffness is varied directly using blends of chemically identical, physically crosslinking elastomers, thus avoiding possible temperature-induced variations in electric and ionic conductivity. Avoiding a chemically crosslinking system rules out variations due to crosslinkers or initiators. Measurements were carried out with a hemispherical indenter resting on a slab of the material with constant load. A theory recently proposed by Zhao and Suo was adapted to the experimental conditions and found to apply well, with no free fitting parameters.

Electrically Tunable Polymer DFB Laser

IC A IO N In recent years, there is a trend in optics shifting from hard static objects, such as lenses and fi bers, to softer objects based on fl exible polymers or fl uids. Soft matter based optics can be tuned by external mechanical devices, but can also be coupled to electroactive polymer “artifi cial muscles”, for instance to provide for voltage-controlled, monolithically integrated optical elements. Soft electromechanically active optics could enable a whole new paradigm for compact and effi cient optical devices. We demonstrate the compact monolithic integration of a fl exible polymer distributed feedback (DFB) dye laser with an electroactive dielectric elastomer actuator. This combination enables direct voltage control of the DFB grating period through compression, such that an actuation voltage up to 3.25 kV leads to a continuous wavelength shift from 604 nm to 557 nm, a change of 7.8%. The solid glass lens is the fi rst choice for beam shaping. Researchers have shown that lens-shaped water droplets can be manipulated electrically for fast tuning of focal length, [ 1 , 2 ]

Strongly enhanced sensitivity in elastic capacitive strain sensors

Strain sensors based on dielectric elastomer capacitors function by the direct coupling of mechanical deformations with the capacitance. The coupling can be improved by enhancing the relative permittivity of the dielectric elastomer. Here, this is carried out through the grafting of conducting polymer (poly-aniline) to the elastomer backbone, leading to molecular composites. An enhancement in capacitance response of 46 times is observed. This could help to extend the possible range of miniaturization towards even smaller device features.

Two types of transitions to wrinkles in dielectric elastomers

A membrane of a dielectric elastomer coated with compliant electrodes may form wrinkles as the applied voltage is ramped up. We present a combination of experiment and theory to investigate the transition to wrinkles using a clamped membrane subject to a constant force and a voltage ramp. Two types of transitions are identified. In type-I transition, the voltage–stretch curve is N-shaped, and flat and wrinkled regions coexist in separate areas of the membrane. The type-I transition progresses by nucleation of small wrinkled regions, followed by the growth of the wrinkled regions at the expense of the flat regions, until the entire membrane is wrinkled. By contrast, in type-II transition, the voltage–stretch curve is monotonic, and the entire flat membrane becomes wrinkled with no nucleation barrier. The two types of transitions are analogous to the first and the second order phase transitions. While the type-I transition is accompanied by a jump in the vertical displacement, type-II transition is accompanied by a continuous change in the vertical displacement. Such transitions may enable applications in muscle-like actuation and energy harvesting, where large deformation and large energy of conversion are desired.