Maziar Sedighi Moghaddam

Wettability and swelling of acetylated and furfurylated wood analyzed by multicycle Wilhelmy plate method

Abstract The wetting, dimensional stability and sorption properties of a range of modified wood samples obtained either by acetylation or furfurylation were compared with those of unmodified samples of the same wood species via a multicycle Wilhelmy plate method. Wettability measurements were performed with water and octane as the swelling and non-swelling liquids, respectively. It was found that acetylation reduces water uptake mainly by reducing the swelling. In comparison, furfurylation reduces both swelling and the void volume in the sample. To quantify the effect of the modification process of the wood properties, the parameters “liquid up-take reduction” and the “perimeter change reduction” were introduced, which were determined from multicycle Wilhelmy plate measurements. Compared with the acetylated wood, the furfurylated wood with a higher level of weight percent gain exhibited larger property changes on the surface and in terms of swelling and sorption properties.

Hydrophobisation of wood surfaces by combining liquid flame spray (LFS) and plasma treatment: dynamic wetting properties

Abstract The hydrophilic nature of wood surfaces is a major cause for water uptake and subsequent biological degradation and dimensional changes. In the present paper, a thin transparent superhydrophobic layer on pine veneer surfaces has been created for controlling surface wettability and water repellency. This effect was achieved by means of the liquid flame spray (LFS) technique, in the course of which the nanoparticulate titanium dioxide (TiO2) was brought to the surface, followed by plasma polymerisation. Plasma polymerised perfluorohexane (PFH) or hexamethyldisiloxane (HMDSO) were then deposited onto the LFS-treated wood surfaces. The same treatment systems were applied to silicon wafers so as to have well-defined reference surfaces. The dynamic wettability was studied by the multicycle Wilhelmy plate (mWP) method, resulting in advancing and receding contact angles as well as sorption behavior of the samples during repeated wetting cycles in water. Atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) were employed to characterise the topography and surface chemical compositions and to elucidate the question how the morphology of the nanoparticles and plasma affect the wetting behavior. A multi-scale roughness (micro-nano roughness) was found and this enhanced the forced wetting durability via a superhydrophobic effect on the surface, which was stable even after repeated wetting cycles. The hydrophobic effect of this approach was higher compared to that of plasma modified surfaces with their micro-scale modification.

Multicycle wilhelmy plate method for wetting properties, swelling and liquid sorption of wood

A multicycle Wilhelmy plate method has been developed to investigate wetting properties, liquid sorption, and swelling of porous substrates such as wood. The use of the method is exemplified by studies of wood veneers of Scots pine sapwood and heartwood, which were subjected to repeated immersion and withdrawal in a swelling liquid (water) and in a nonswelling liquid (octane). The swelling liquid changes the sample dimensions during measurements, in particular its perimeter. This, in turn, influences the force registered. A model based on a linear combination of the measured force and final change in sample perimeter is suggested, and validated to elucidate the dynamic perimeter change of wood veneer samples. We show that pine heartwood and pine sapwood differ in several respects in their interaction with water. Pine heartwood showed (i) lower liquid uptake, (ii) lower swelling, (iii) higher contact angle, and (iv) lower level of dissolution of surface active components (extractives) than pine sapwood. We conclude that the method is also suitable for studying wetting properties of other porous and swellable materials. The wettability results were supported by surface chemical analysis using X-ray photoelectron spectroscopy, showing higher extractives and lignin content on heartwood than on sapwood surfaces.

Wettability and liquid sorption of wood investigated by Wilhelmy plate method

The wettability of Scots pine veneers was investigated with different approaches using the Wilhelmy plate method. The probe liquids were water and octane, which differ; in that, water is able to swell the wood sample, whereas octane does not. Novel approaches based on the Wilhelmy plate method to study wettability, liquid penetration, and swelling behavior of wood veneers are introduced. First, immersion to constant depth was performed, and liquid uptake with time was evaluated. Different kinetic regimes, the fastest one associated with contact angle changes and the slowest regime associated with liquid sorption by capillary and diffusion, were observed. Two other approaches, imbibition at constant depth (with initial deeper immersion) and full immersion, were utilized in order to keep the contact angle constant during measurements. Dynamic wettability studies were done by a multi-cycle (10–20 cycles) Wilhelmy method. Based on this, the time-dependent swelling of wood and changes in sample perimeter could be obtained. Generally, water showed higher absorption than octane. In all wettability studies, and for both probe liquids, the penetration process starts with a fast initial sorption, which is followed by swelling in the case of water.

Wetting hysteresis induced by temperature changes: Supercooled water on hydrophobic surfaces.

The state and stability of supercooled water on (super)hydrophobic surfaces is crucial for low temperature applications and it will affect anti-icing and de-icing properties. Surface characteristics such as topography and chemistry are expected to affect wetting hysteresis during temperature cycling experiments, and also the freezing delay of supercooled water. We utilized stochastically rough wood surfaces that were further modified to render them hydrophobic or superhydrophobic. Liquid flame spraying (LFS) was utilized to create a multi-scale roughness by depositing titanium dioxide nanoparticles. The coating was subsequently made non-polar by applying a thin plasma polymer layer. As flat reference samples modified silica surfaces with similar chemistries were utilized. With these substrates we test the hypothesis that superhydrophobic surfaces also should retard ice formation. Wetting hysteresis was evaluated using contact angle measurements during a freeze-thaw cycle from room temperature to freezing occurrence at -7°C, and then back to room temperature. Further, the delay in freezing of supercooled water droplets was studied at temperatures of -4°C and -7°C. The hysteresis in contact angle observed during a cooling-heating cycle is found to be small on flat hydrophobic surfaces. However, significant changes in contact angles during a cooling-heating cycle are observed on the rough surfaces, with a higher contact angle observed on cooling compared to during the subsequent heating. Condensation and subsequent frost formation at sub-zero temperatures induce the hysteresis. The freezing delay data show that the flat surface is more efficient in enhancing the freezing delay than the rougher surfaces, which can be rationalized considering heterogeneous nucleation theory. Thus, our data suggests that molecular flat surfaces, rather than rough superhydrophobic surfaces, are beneficial for retarding ice formation under conditions that allow condensation and frost formation to occur.

Microstructure of chemically modified wood using X-ray computed tomography in relation to wetting properties

Abstract X-ray computed tomography (XCT) was utilized to visualize and quantify the 2D and 3D microstructure of acetylated southern yellow pine (pine) and maple, as well as furfurylated pine samples. The total porosity and the porosity of different cell types, as well as cell wall thickness and maximum opening of tracheid lumens were evaluated. The wetting properties (swelling and capillary uptake) were related to these microstructural characteristics. The data show significant changes in the wood structure for furfurylated pine sapwood samples, including a change in tracheid shape and filling of tracheids by furan polymer. In contrast, no such changes were noted for the acetylated pine samples at the high resolution of 0.8 μm. The XCT images obtained for the furfurylated maple samples demonstrated that all ray cells and some vessel elements were filled with furan polymer while the fibers largely remained unchanged. Furfurylation significantly decreased the total porosity of both the maple and pine samples. Furthermore, this was observed in both earlywood (EW) and latewood (LW) regions in the pine samples. In contrast, the total porosity of pine samples was hardly affected by acetylation. These findings are in line with wetting results demonstrating that furfurylation reduces both swelling and capillary uptake in contrast to acetylation which reduces mostly swelling. Furfurylation significantly increased the cell wall thickness of both the maple and pine samples, especially at higher levels of furfurylation.

Liquid sorption, swelling and surface energy properties of unmodified and thermally modified Scots pine heartwood after extraction

Abstract The effect of extractives removal on liquid sorption, swelling and surface energy properties of unmodified wood (UW) and thermally modified Scots pine heartwood (hW) (TMW) was studied. The extraction was performed by a Soxtec procedure with a series of solvents and the results were observed by the multicycle Wilhelmy plate method, inverse gas chromatography (IGC) and Fourier transform infrared (FTIR) spectroscopy. A significantly lower rate of water uptake was found for the extracted UW, compared with the unextracted one. This is due to a contamination effect in the latter case from water-soluble extractives increasing the capillary flow into the wood voids, proven by the decreased water surface tension. The swelling in water increased after extraction 1.7 and 3 times in the cases of UW and TMW, respectively. The dispersive part of the surface energy was lower for the extracted TMW compared to the other sample groups, indicating an almost complete removal of the extractives. The FTIR spectra of the extracts showed the presence of phenolic compounds but also resin acids and aliphatic compounds.