Morten P. Bakker

H1 photonic crystal cavities for hybrid quantum information protocols

Hybrid quantum information protocols are based on local qubits, such as trapped atoms, NV centers, and quantum dots, coupled to photons. The coupling is achieved through optical cavities. Here we demonstrate far-field optimized H1 photonic crystal membrane cavities combined with an additional back reflection mirror below the membrane that meet the optical requirements for implementing hybrid quantum information protocols. Using numerical optimization we find that 80% of the light can be radiated within an objective numerical aperture of 0.8, and the coupling to a single-mode fiber can be as high as 92%. We experimentally prove the unique external mode matching properties by resonant reflection spectroscopy with a cavity mode visibility above 50%.

Homodyne detection of coherence and phase shift of a quantum dot in a cavity.

A homodyne measurement technique is demonstrated that enables direct observation of the coherence and phase of light that passed through a coupled quantum dot (QD)-microcavity system, which in turn enables clear identification of coherent and incoherent QD transitions. As an example, we study the effect of power-induced decoherence, where the QD transition saturates and incoherent emission from the excited state dominates at higher power. Further, we show that the same technique allows measurement of the quantum phase shift induced by a single QD in the cavity, which is strongly enhanced by cavity quantum electrodynamics effects.

Purification of a single-photon nonlinearity

Single photon nonlinearities based on a semiconductor quantum dot in an optical microcavity are a promising candidate for integrated optical quantum information processing nodes. In practice, however, the finite quantum dot lifetime and cavity-quantum dot coupling lead to reduced fidelity. Here we show that, with a nearly polarization degenerate microcavity in the weak coupling regime, polarization pre- and postselection can be used to restore high fidelity. The two orthogonally polarized transmission amplitudes interfere at the output polarizer; for special polarization angles, which depend only on the device cooperativity, this enables cancellation of light that did not interact with the quantum dot. With this, we can transform incident coherent light into a stream of strongly correlated photons with a second-order correlation value up to 40, larger than previous experimental results, even in the strong-coupling regime. This purification technique might also be useful to improve the fidelity of quantum dot based logic gates.

Polarization degenerate micropillars fabricated by designing elliptical oxide apertures

A method for fabrication of polarization degenerate oxide apertured micropillar cavities is demonstrated. Micropillars are etched such that the size and shape of the oxide front is controlled. The polarization splitting in the circular micropillar cavities due to the native and strain induced birefringence can be compensated by elongating the oxide front in the [110] direction, thereby reducing stress in this direction. By using this technique, we fabricate a polarization degenerate cavity with a quality factor of 1.7 × 104 and a mode volume of 2.7 μm3, enabling a calculated maximum Purcell factor of 11.

Monitoring the formation of oxide apertures in micropillar cavities

An imaging technique is presented that enables monitoring of the wet thermal oxidation of a thin AlAs layer embedded between two distributed Bragg reflector mirrors in a micropillar. After oxidation we confirm by white light reflection spectroscopy that high quality optical modes confined to a small volume have been formed. The combination of these two optical techniques provides a reliable and efficient way of producing oxide apertured micropillar cavities for which the wet thermal oxidation is a critical fabrication step.

Quantum dot nonlinearity through cavity-enhanced feedback with a charge memory

In an oxide apertured quantum dot (QD) micropillar cavity-QED system, we found strong QD hysteresis effects and lineshape modifications even at very low intensities corresponding to less than 0.001 intracavity photons. We attribute this to the excitation of charges by the intracavity field; charges that get trapped at the oxide aperture, where they screen the internal electric field and blueshift the QD transition. This in turn strongly modulates light absorption by cavity QED effects, eventually leading to the observed hysteresis and lineshape modifications. The cavity also enables us to observe the QD dynamics in real time, and all experimental data agrees well with a power-law charging model. This effect can serve as a novel tuning mechanism for quantum dots.

Fine tuning of micropillar cavity modes through repetitive oxidations

Repetitive wet thermal oxidations of a tapered oxide aperture in a micropillar structure are demonstrated. After each oxidation step the confined optical modes are analyzed at room temperature. Three regimes are identified. First, the optical confinement increases when the aperture oxidizes toward the center. Then, the cavity modes shift by more than 30 nm when the taper starts to oxidize through the center, leading to a decrease in the optical path length. Finally, the resonance frequency levels off when the aperture is oxidized all the way through the micropillar, but confined optical modes with a high quality factor remain. This repetitive oxidation technique therefore enables precise control of the optical cavity volume or wavelength.

Single and Coupled Photonic Crystal Cavities for Solid-State Cavity-QED

We discuss the implementation of quantum information schemes with quantum dots in photonic crystal cavities, focusing on the optimization of far-field emission profiles and independent electrical tuning on quantum dots in waveguide-coupled cavities

Cavity-QED with quantum dots in oxide-apertured micropillars

We describe quantum information schemes involving photon polarization and the spin of a single electron trapped in a self-assembled quantum dot. Such schemes are based on spin-selective reflection in the weak-coupling regime of cavity quantum electrodynamics. We discuss their practical implementation in oxide-apertured micropillar cavities. We introduce a technique, based on the creation of small surface defects by means of a focused intense laser beam, to permanently tune the optical properties of the microcavity without damaging the cavity quality. This technique allows low-temperature polarization-selective tuning of the frequencies of the cavity modes and the quantum dot optical transitions.

Single and coupled L3 photonic crystal cavities for cavity-QED experiments

Here we discuss the experimental characterization of the spatial far-field profiles for the confined modes in a photonic crystal cavity of the L3 type, finding a good agreement with FDTD simulations. We then link the far-field profiles to relevant features of the cavity mode near-fields, using a simple Fabry-Perot resonator model. Finally, we describe a technique for independent all-electrical control of the wavelength of quantum dots in separated L3 cavities, coupled by a waveguide, by electrical isolation via proton implantation