Robert P. Eganhouse

Crude oil in a shallow sand and gravel aquifer-III. Biogeochemical reactions and mass balance modeling in anoxic groundwater

Abstract Crude oil floating on the water table in a sand and gravel aquifer provides a constant source of hydrocarbons to the groundwater at a site near Bemidji, Minnesota. The degradation of hydrocarbons affects the concentrations of oxidized and reduced aqueous species in the anoxic part of the contaminant plume that developed downgradient from the oil body. The concentrations of Fe2+, Mn2+ and CH4, Eh measurements, and the δ13C ratios of the total inorganic C indicate that the plume became more reducing ver a 5-a period. However, the size of the contaminant plume remained stable during this time. Field data coupled with laboratory microcosm experiments indicate that benzene and the alkylbenzenes are degraded in an anoxic environment. In anaerobic microcosm experiments conducted under field conditions, almost complete degradation (98%) was observed for benzene in 125 d and for toluene in 45 d. Concentrations of aqueous Fe2+ and Mn2+ increased in these experiments, indicating that the primary reactions were hydrocarbon degradation coupled with Fe and Mn reduction. Mass transfer calculations on a 40-m flowpath in the anoxic zone, downgradient from the oil body, indicated that the primary reactions in the anoxic zone are oxidation of organic compounds, precipitation of siderite and a ferroan calcite, dissolution of iron oxide and outgassing of CH4 and CO2. The major difference in the two models presented is the ratio of CO2 and CH4 that outgasses. Both models indicate quantitatively that large amounts of Fe are dissolved and reprecipitated as ferrous iron in the anoxic zone of the contaminant plume.

Progression of natural attenuation processes at a crude-oil spill site . I. Geochemical evolution of the plume

A 16-year study of a hydrocarbon plume shows that the extent of contaminant migration and compound-specific behavior have changed as redox reactions, most notably iron reduction, have progressed over time. Concentration changes at a small scale, determined from analysis of pore-water samples drained from aquifer cores, are compared with concentration changes at the plume scale, determined from analysis of water samples from an observation well network. The small-scale data show clearly that the hydrocarbon plume is growing slowly as sediment iron oxides are depleted. Contaminants, such as ortho-xylene that appeared not to be moving downgradient from the oil on the basis of observation well data, are migrating in thin layers as the aquifer evolves to methanogenic conditions. However, the plume-scale observation well data show that the downgradient extent of the Fe2+ and BTEX plume did not change between 1992 and 1995. Instead, depletion of the unstable Fe (III) oxides near the subsurface crude-oil source has caused the maximum dissolved iron concentration zone within the plume to spread at a rate of approximately 3 m/year. The zone of maximum concentrations of benzene, toluene, ethylbenzene and xylene (BTEX) has also spread within the anoxic plume. In monitoring the remediation of hydrocarbon-contaminated ground water by natural attenuation, subtle concentration changes in observation well data from the anoxic zone may be diagnostic of depletion of the intrinsic electron-accepting capacity of the aquifer. Recognition of these subtle patterns may allow early prediction of growth of the hydrocarbon plume.

The geochemical evolution of low-molecular-weight organic acids derived from the degradation of petroleum contaminants in groundwater

Abstract The geochemical evolution of low-molecular-weight organic acids in groundwater downgradient from a crude-oil spill near Bemidji, Minnesota, was studied over a five year period (1986–1990). The organic acids are metabolic intermediates of the degradation of components of the crude oil and are structurally related to hydrocarbon precursors. The concentrations of organic acids, particularly aliphatic acids, increase as the microbial alteration of hydrocarbons progresses. The organic-acid pool changes in composition and concentration over time and in space as the degradation processes shift from Fe(III) reduction to methanogenesis. Over time, the aquifer system evolves into one in which the groundwater contains more oxidized products of hydrocarbon degradation and the reduced forms of iron, manganese, and nitrogen. Laboratory microcosm experiments with aquifer material support the hypothesis that organic acids observed in the groundwater originate from the microbial degradation of aromatic hydrocarbons under anoxic conditions. The geochemistry of two other shallow aquifers in coastal plain sediments, one contaminated with creosote waste and the other with gasoline, were compared to the Bemidji site. The geochemical evolution of the low-molecular-weight organic acid pool in these systems is controlled, in part, by the presence of electron acceptors available for microbially mediated electron-transfer reactions. The depletion of electron acceptors in aquifers leads to the accumulation of aliphatic organic acids in anoxic groundwater.

Transformation of Monoaromatic hydrocarbons to organic acids in anoxic groundwater environment

The transformation of benzene and a series of alkylbenzenes was studied in anoxic groundwater of a shallow glacial-outwash aquifer near Bemidji, Minnesota, U.S.A. Monoaromatic hydrocarbons, the most water-soluble components of crude oil, were transported downgradient of an oil spill, forming a plume of contaminated groundwater. Organic acids that were not original components of the oil were identified in the anoxic groundwater. The highest concentrations of these oxidized organic compounds were found in the anoxic plume where a decrease in concentrations of structurally related alkylbenzenes was observed. These results suggest that biological transformation of benzene and alkylbenzenes to organic acid intermediates may be an important attenuation process in anoxic environments. The transformation of a complex mixture of hydrocarbons to a series of corresponding oxidation products in an anoxic subsurface environment provides new insight into in situ anaerobic degradation processes.

Crude oil in a shallow sand and gravel aquifer-II. Organic geochemistry

Abstract Crude oil spilled from a pipeline break in a remote area of north-central Minnesota has contaminated a shallow glacial outwash aquifer. Part of the oil was sprayed over a large area to the west of the pipeline and part of it accumulated in an oil body that floats at the water table to the east of the point of discharge. Total dissolved organic carbon (TDOC) concentrations in shallow groundwater collected in the oil spray area reach 16 mg/l. This is nearly an order of magnitude higher than the TDOC concentrations of native groundwater (∼2–3mg/l). The additional TDOC derives from the partial degradation of petroleum residues deposited at the land surface and transported to the aquifer by vertical recharge. In the vicinity of the oil body, TDOC concentrations in groundwater are 48 mg/l, 58% of the TDOC being composed of non-volatile organic C. The majority of the volatile DOC (63%) is a mixture of low-molecular-weight saturated, aromatic and alicyclic hydrocarbons derived from the oil. Downgradient from the oil body along the direction of groundwater flow, concentrations of all measured constituents of the TDOC pool decrease. Concentrations begin to decline most rapidly, however, in the zone where dissolved O 2 concentrations begin to increase, ∼50m downgradient from the leading edge of the oil. Within the anoxic zone near the oil body, removal rates of isometric monoaromatic hydrocarbons vary widely. This indicates that the removal processes are mediated mainly by microbiological activity. Molecular and spectroscopic characterization of the TDOC and its spatial and temporal variation provide evidence of the importance of biogeochemical processes in attenuating petroleum contaminants in this perturbed subsurface environment.

Assessment of PDMS-Water Partition Coefficients: Implications for Passive Environmental Sampling of Hydrophobic Organic Compounds

Solid-phase microextraction (SPME) has shown potential as an in situ passive-sampling technique in aquatic environments. The reliability of this method depends upon accurate determination of the partition coefficient between the fiber coating and water (K(f)). For some hydrophobic organic compounds (HOCs), K(f) values spanning 4 orders of magnitude have been reported for polydimethylsiloxane (PDMS) and water. However, 24% of the published data examined in this review did not pass the criterion for negligible depletion, resulting in questionable K(f) values. The range in reported K(f) is reduced to just over 2 orders of magnitude for some polychlorinated biphenyls (PCBs) when these questionable values are removed. Other factors that could account for the range in reported K(f), such as fiber-coating thickness and fiber manufacturer, were evaluated and found to be insignificant. In addition to accurate measurement of K(f), an understanding of the impact of environmental variables, such as temperature and ionic strength, on partitioning is essential for application of laboratory-measured K(f) values to field samples. To date, few studies have measured K(f) for HOCs at conditions other than at 20° or 25 °C in distilled water. The available data indicate measurable variations in K(f) at different temperatures and different ionic strengths. Therefore, if the appropriate environmental variables are not taken into account, significant error will be introduced into calculated aqueous concentrations using this passive sampling technique. A multiparameter linear solvation energy relationship (LSER) was developed to estimate log K(f) in distilled water at 25 °C based on published physicochemical parameters. This method provided a good correlation (R(2) = 0.94) between measured and predicted log K(f) values for several compound classes. Thus, an LSER approach may offer a reliable means of predicting log K(f) for HOCs whose experimental log K(f) values are presently unavailable. Future research should focus on understanding the impact of environmental variables on K(f). Obtaining the data needed for an LSER approach to estimate K(f) for all environmentally relevant HOCs would be beneficial to the application of SPME as a passive-sampling technique.

Inverse modeling of BTEX dissolution and biodegradation at the Bemidji, MN crude-oil spill site.

The U.S. Geological Survey (USGS) solute transport and biodegradation code BIOMOC was used in conjunction with the USGS universal inverse modeling code UCODE to quantify field-scale hydrocarbon dissolution and biodegradation at the USGS Toxic Substances Hydrology Program crude-oil spill research site located near Bemidji, MN. This inverse modeling effort used the extensive historical data compiled at the Bemidji site from 1986 to 1997 and incorporated a multicomponent transport and biodegradation model. Inverse modeling was successful when coupled transport and degradation processes were incorporated into the model and a single dissolution rate coefficient was used for all BTEX components. Assuming a stationary oil body, we simulated benzene, toluene, ethylbenzene, m,p-xylene, and o-xylene (BTEX) concentrations in the oil and ground water, respectively, as well as dissolved oxygen. Dissolution from the oil phase and aerobic and anaerobic degradation processes were represented. The parameters estimated were the recharge rate, hydraulic conductivity, dissolution rate coefficient, individual first-order BTEX anaerobic degradation rates, and transverse dispersivity. Results were similar for simulations obtained using several alternative conceptual models of the hydrologic system and biodegradation processes. The dissolved BTEX concentration data were not sufficient to discriminate between these conceptual models. The calibrated simulations reproduced the general large-scale evolution of the plume, but did not reproduce the observed small-scale spatial and temporal variability in concentrations. The estimated anaerobic biodegradation rates for toluene and o-xylene were greater than the dissolution rate coefficient. However, the estimated anaerobic biodegradation rates for benzene, ethylbenzene, and m,p-xylene were less than the dissolution rate coefficient. The calibrated model was used to determine the BTEX mass balance in the oil body and groundwater plume. Dissolution from the oil body was greatest for compounds with large effective solubilities (benzene) and with large degradation rates (toluene and o-xylene). Anaerobic degradation removed 77% of the BTEX that dissolved into the water phase and aerobic degradation removed 17%. Although goodness-of-fit measures for the alternative conceptual models were not significantly different, predictions made with the models were quite variable.

Diagenetic fate of organic contaminants on the Palos Verdes Shelf, California

Municipal wastes discharged through deepwater submarine outfalls since 1937 have contaminated sediments of the Palos Verdes Shelf. A site approximately 6–8 km downcurrent from the outfall system was chosen for a study of the diagenetic fate of organic contaminants in the waste-impacted sediments. Concentrations of three classes of hydrophobic organic contaminants (DDT+metabolites, polychlorinated biphenyls (PCBs), and the long-chain alkylbenzenes) were determined in sediment cores collected at the study site in 1981 and 1992. Differences between the composition of effluent from the major source of DDT (Montrose Chemical) and that found in sediments suggests that parent DDT was transformed by hydrolytic dehydrochlorination during the earliest stages of diagenesis. As a result, p,p′-DDE is the dominant DDT metabolite found in shelf sediments, comprising 60–70% of ΣDDT. The p,p-DDE/p,p′-DDMU concentration ratio decreases with increasing sub-bottom depth in sediment cores, indicating that reductive dechlorination of p,p′-DDE is occurring. Approximately 9–23% of the DDE inventory in the sediments may have been converted to DDMU since DDT discharges began ca. 1953. At most, this is less than half of the decline in p,p′-DDE inventory that has been observed at the study site for the period 1981–1995. Most of the observed decrease is attributable to remobilization by processes such as sediment mixing coupled to resuspension, contaminant desorption, and current advection. Existing field data suggest that the in situ rate of DDE transformation is 102–103 times slower than rates determined in recent laboratory microcosm experiments (Quensen, J.F., Mueller, S.A., Jain, M.K., Tiedje, J.M., 1998. Reductive dechlorination of DDE to DDMU in marine sediment microcosms. Science, 280, 722–724.). This explains why the DDT composition (i.e. o,p′-, p,p′-isomers of DDE, DDD, DDT) of sediments from this site have not changed significantly since at least 1972. Congener-specific PCB compositions in shelf sediments are highly uniform and show no evidence of diagenetic transformation. Apparently, the agents/factors responsible for reductive dechlorination of DDE are not also effecting alteration of the PCBs. Two types of long-chain alkylbenzenes were found in the contaminated sediments. Comparison of chain length and isomer distributions of the linear alkylbenzenes in wastewater effluent and surficial sediment samples indicate that these compounds undergo biodegradation during sedimentation. Further degradation of the linear alkylbenzenes occurs after burial despite relatively invariant isomer compositions. The branched alkylbenzenes are much more persistent than the linear alkylbenzenes, presumably due to extensive branching of the alkyl side chain. Based on these results, p,p′-DDE, PCBs, and selected branched alkylbenzenes are sufficiently persistent for use in molecular stratigraphy. The linear alkylbenzenes may also provide information on depositional processes. However, their application as quantitative molecular tracers should be approached with caution.

Extractable organic matter in municipal wastewaters. 2. Hydrocarbons: molecular characterization

Hydrocarbons isolated from southern California municipal wastewaters were analyzed by high-resolution gas chromatography and computer-assisted gas chromatography-mass spectrometry. Most of the hydrocarbons (56-77%) are not chromatographically resolvable and probably derive from petroleum products such as lubricating oils. Normal, iso-, and acyclic isoprenoid alkanes along with alkylcyclohexanes and numerous series of substituted benzenes and polycyclic aromatic hydrocarbons compose the major fraction of the resolvable hydrocarbons. Polycyclic terpenoids occur as trace constituents and appear also to be of ancient, not recent biosynthetic, origin. However, the virtual absence of 17..cap alpha..(H),18..cap alpha..(H),21..beta..(H)-28,30-dinorhopane, a specific marker of California oils, indicates that locally produced petroleum is, at most, a minor contributor to these wastewaters. A homologous series of long-chain alkylbenzenes presumably derived from the LAS-type detergents was identified. These compounds seem to be abundant and ubiquitous domestic wastewater constituents that might be exploited as anthropogenic waste tracers in the marine environment.

Use of molecular markers for the detection of municipal sewage sludge at sea

The concentrations of two classes of waste-specific molecular markers (the linear alkylbenzenes and the fecal sterols, coprostanol and epicoprostanol) were determined in six municipal sewage sludges. Total linear alkylbenzene concentrations ranged from 150 to 7300 μg liter−1, whereas coprostanol was present at levels approximately one order of magnitude higher (2·6 to 55 mg liter−1). Experiments were performed to establish the limits of detection and quantitation for these compounds in small volume (< c. 2 liters) bulk water samples using high resolution gas chromatography and gas chromatography/mass spectrometry. In an effort to simulate the degree of dilution expected during the dumping of sludge in waters of the continental slope, water was mixed with the sludge samples in varying proportions (103:1 to 106:1), and the concentrations of the markers were determined. Comparison of the estimated limits of quantitation with marker concentrations measured in the diluted sludges showed that reliable quantitation of the linear alkylbenzenes was possible at dilutions less than 106:1. Coprostanol and epicoprostanol, however, were measurable at a dilution of 106:1). If background levels of the markers in blanks are reduced and larger volume water samples are processed at sea, it should be possible to extend present measurement capabilities to dilutions one to two orders of magnitude beyond those reported here. These results indicate that molecular markers can be used to monitor the short-term fate of sewage sludge in the deep ocean.