Silvia Amélia Scudeler Vedovello

Effects of thermocycling and light source on the bond strength of metallic brackets to bovine teeth

This study evaluated the effects of thermocycling and different light sources on the bond strength of metallic brackets to bovine tooth enamel using an adhesive resin. Bovine teeth were etched with 35% phosphoric acid gel for 20 s. After application of primer, metallic brackets were bonded to the buccal surface using Transbond XT, forming 8 groups (n = 20), depending on the light source used for photoactivation (AccuCure 3000 argon laser--20 s, Apollo 95E plasma arc--12 s, UltraLume 5 LED--40 s and XL2500 halogen light--40 s) and experimental conditions without (Groups 1 to 4) or with thermocycling (Groups 5 to 8). Shear bond testing was carried out after 24 h of distilled water storage (Groups 1 to 4) or storage and thermocycling in distilled water (groups 5 to 8; 1,500 cycles--5°/55 °C). Data were subjected to two-way ANOVA and Tukeys test (α = 0.05). The Adhesive Remnant Index (ARI) was evaluated at ×8 magnification. No significant differences (p>0.05) in bond strength were found when the conditions without and with thermocycling were compared for any of the light sources. No significant differences (p>0.05) in bond strength were found among the light sources, irrespective of performing or not thermocycling. There was a predominance of ARI scores 1 in all groups. In conclusion, light sources and thermocycling had no influence on the bond strength of brackets to bovine enamel.

Effect of bonding material, etching time and silane on the bond strength of metallic orthodontic brackets to ceramic

The purpose of this study was to evaluate the bond strength of metallic orthodontic brackets to feldspathic ceramic with different etching times, bonding materials and with or without silane application. Cylinders of feldspathic ceramic were etched with 10% hydrofluoric acid for 20 or 60 s. For each etching time, half of the cylinders received two layers of silane. Metallic brackets were bonded to the cylinders using Transbond XT (3M Unitek) or Fuji Ortho LC (GC). Light-activation was carried out with total exposure time of 40 s using UltraLume 5. Shear bond strength testing was performed after 24 h storage. Data were submitted to three-way ANOVA and Tukeys test (α=0.05). The adhesive remnant index (ARI) was used to evaluate the amount of adhesive remaining on the ceramic surface at ×8 magnification. Specimens etched for 60 s had significantly higher bond strength compared with 20 s. The application of silane was efficient in increasing the shear bond strength between ceramic and both fixed materials. Transbond XT showed significantly higher (p<0.05) bond strength than Fuji Orth LC. There was a predominance of ARI score 0 (clean ceramic failure surface) for all groups, with an increase in scores 1, 2 and 3 (adhesive material increasingly present on ceramic failure aspect) for the 60-s etching time. In conclusion, 60-s etching time, silane and Transbond XT improved significantly the shear bond strength of brackets to ceramic.

Antimicrobial effect of Melaleuca alternifolia dental gel in orthodontic patients.

The aim of this study was to evaluate the antimicrobial effect and sensorial analysis of the gel developed with the essential oil of Melaleuca alternifolia. Thirty-four volunteers, divided into 2 groups, were monitored for 4 weeks. Initially, clinical biofilm (plaque index) and saliva samples (bacteria count) were collected, from which the standard values for each patient were obtained. For 7 days, group 1 used the melaleuca gel (Petite Marie/All Chemistry, São Paulo, Brazil), and group 2 used Colgate Total (S.B. Campo, São Paulo, Brazil). After 7 days, the plaque index was performed again, as well as the bacteria count and the sensorial analysis (appearance, color, odor, brightness, viscosity, and first taste sensation). The volunteers were instructed to return to their usual dental hygiene habits for 15 days. After this, group 1 started using Colgate Total, and group 2 started using the melaleuca gel, with the same evaluation procedures as the first week. The data were analyzed statistically with a significance level of 5%. In the bacteria count and clinical disclosure, the melaleuca gel was more effective in decreasing the dental biofilm and the numbers of bacteria colonies. According to the data from the sensory evaluation, Colgate Total (the control) showed better results regarding flavor and first sensation (P <0.05). We concluded that melaleuca gel is efficient in bacteria control but needs improvement in taste and first sensation.

Influence of Water Storage and Bonding Material on Bond Strength of Metallic Brackets to Ceramic

This study investigated the influence of water storage (24 h and 6 months), and Transbond XT and Fuji Ortho LC bonding materials on the bond strength of metallic brackets bonded to feldspathic ceramic. Four cylinders of feldspathic ceramic were etched with 10% hydrofluoric acid for 60 s. Each cylinder received two layers of silane. Metallic brackets were bonded to the cylinders using Transbond XT or Fuji Ortho LC. Light-activation was carried out with 40 s total exposure time using Bluephase G2. Half the specimens for each bonding materials (n=20) were stored in distilled water at 37 °C for 24 h and the other half for 6 months. Shear bond strength testing was performed after storage times at a crosshead speed of 1 mm/min. The adhesive remnant index (ARI) was used to evaluate the amount of adhesive remaining on the ceramic surface at ×8 magnification. Data were subjected to two-way ANOVA and Tukeys test (p<0.05). Transbond XT showed significantly higher bond strength (p<0.05) than Fuji Ortho LC. Significant differences in bond strength (p<0.05) were found when 24 h and 6 months storage times were compared between materials. ARI showed a predominance of score 0 for all groups, and higher scores at 1, 2 and 3 for 24 h storage time. In conclusion, storage time and bonding materials showed significant influence on the bond strength of brackets to ceramic.

Effect of activation mode on shear bond strength of metallic brackets.

The aim of this study was to evaluate the shear bond strength (SBS) of metallic orthodontic brackets bonded to bovine teeth using light-activated or chemically activated composite resins. One hundred and twenty bovine mandibular incisors were divided into 6 groups (n=20), according to the bonding materials: Transbond XT (T); Enforce Dual (ED); Enforce chemical (EC); Enforce Light-activated (EL); Concise Orthodontic (C); and RelyX Unicem Capsule (UN). Metallic brackets were positioned and firmly bonded to the teeth. Light-activation for T, ED, EL and UN was carried out with four exposures on each side of the bracket with 20 s total exposure times using XL2500 (3M ESPE). EC and C were chemically cured. Next, all specimens were stored in deionized water at 37 °C for 24 h. The shear bond strength was carried out at a crosshead speed of 1.0 mm/min. Data were subjected to one-way ANOVA and Tukeys test (α=0.05). The adhesive remnant index (ARI) was evaluated at 8× magnification. C (17.72 ± 4.45) presented significantly higher SBS means (in MPa) than the other groups (p<0.05), followed by EC (11.97 ± 5.77) and ED (10.57 ± 1.32). EL (5.39 ± 1.06) and UN (4.32 ± 1.98) showed the lowest SBS means, while T (9.09 ± 2.56) showed intermediate values. For ARI, there was a predominance of score 0 for EC, C and UN, and score 3 for T, ED and EL. In conclusion, the activation mode influenced the SBS.

Influence of Light Source, Thermocycling and Silane on the Shear Bond Strength of Metallic Brackets to Ceramic

The objective of this study was to evaluate the effects of different light sources, thermocycling and silane on the bond strength of metallic brackets to ceramic. Cylinders of feldspathic ceramic were etched with 10% hydrofluoric acid for 60 s. Half of the cylinders (Groups 1 to 4) received two layers of silane. Metallic brackets were bonded to the cylinders using Transbond XT and divided into 8 groups (n=20), according to light source (Radii Plus LED - 40 s; Groups 1, 2, 5 and 6 and XL 2500 halogen light - 40 s; Groups 3, 4, 7 and 8) and experimental conditions with (Groups 2, 4, 6 and 8) without thermocycling (Groups 1, 3, 5 and 7). Shear bond testing was carried out after 24 h of deionized water storage (Groups 1, 3, 5 and 7) and thermocycling (Groups 2, 4, 6 and 8; 7,000 cycles - 5°/55 °C). Date were submitted to three-way ANOVA and Tukeys post hoc test (α=0.05). The Adhesive Remnamt Index (ARI) was evaluated at 8× magnification. The application of silane was effective in increasing the shear bond strength of the brackets to ceramic (p<0.05). Significant difference (p<0.05) on the bond strength was observed between light sources with or without thermocycling. The ARI showed a predominance of scores 0 for all groups, with an increase in scores 1, 2 and 3 for the silane groups. In conclusion, silane improved significantly the shear bond strength of the brackets to ceramic. The thermocycling and light sources influence on the bond strength.

Avaliação longitudinal de arcadas dentárias individualizadas com o método Borda WALA

INTRODUCTION: The form of mandibular arch is considered one of the main references among the diagnostic tools because the maintenance of this arch form and dimension is an important factor for stability of orthodontic treatment. OBJECTIVES: To evaluate the changes in mandibular intercanine and intermolar widths during orthodontic treatment and 3 years of posttreatment, in which the WALA ridge was used for individualization of the mandibular arch form. METHODS: Sample comprised of 20 patients (12 women and 8 men), with a mean age of 20.88 years. The dental casts of the initial, final and post-treatment evaluation were used for measurement of the intercanine and intermolar distances in the center of the buccal surface of the clinical crown and in the width of the WALA ridge. Data were analyzed by means of ANOVA test followed by Tukey test (p<0.05). RESULTS: Indicated that there was a statistically significant difference in intercanine and intermolar distances among the three stages evaluated. These distances increased significantly with treatment, and presented a reduction in the post-treatment period, however not reaching the initial values. CONCLUSIONS: The WALA ridge method used in this study for construction of the individualized diagrams and for measurement of the intercanine and intermolar distances was shown to be valuable, allowing the individualization of the dental arches and favoring the post-treatment stability.

Effect of Acid Etching, Silane and Thermal Cycling on the Bond Strength of Metallic Brackets to Ceramic

The aim of this study was to evaluate the effect of silanes, thermal cycling and acid etching on the shear bond strength (SBS) of metallic brackets to feldspathic ceramic. Feldspathic ceramic cylinders (Groups 1, 2, 5 and 6) were etched for 60 s with 10% hydrofluoric acid and Groups 3, 4, 7 and 8, without acid etching. Two layers of silane Clearfil Ceramic Primer (CCP, Groups 1 to 4) and two layers of RelyX Ceramic Primer (RCP, groups 5 to 8) were applied and dried for 60 s. Brackets were bonded to the cylinders with Transbond XT and light-activated for 40 s with Bluephase G2. All specimens were stored in deionized water at 37 °C for 24 h, and the specimens of groups 1, 3, 5 and 7 were submitted to 7,000 thermal cycles (5 °C/55 °C). After storage, the SBS test was performed at a crosshead speed of 1 mm/min. Data were subjected to three-way ANOVA and Tukeys post hoc test (α=0.05). The adhesive remnant index (ARI) was evaluated at 8x magnification. The SBS of CCP was significantly greater than of RCP (p<0.05), with or without thermal cycling. Thermal cycling significantly reduced the SBS (p<0.05). The groups submitted to acid etching showed significantly higher SBS than those without acid etching (p<0.05). In conclusion, thermal cycling reduced SBS for all groups. The best ceramic surface treatment for bracket bonding was achieved by acid etching and CCP silane. The ARI results showed predominance of score 0 for all groups.

Influence of quality of life, self-perception, and self-esteem on orthodontic treatment need.

Introduction In this study, we aimed to assess the relationship between normative and perceived orthodontic treatment need associated with quality of life, self‐esteem, and self‐perception. Methods The sample included 248 schoolchildren aged 12 years. The normative aspect of orthodontic treatment was assessed by the Dental Health Component and the Aesthetic Component of the Index of Orthodontic Treatment Need. The subjects were further evaluated for their oral health‐related quality of life, self‐esteem, and self‐perception of oral esthetics. The Aesthetic Component of the Index of Orthodontic Treatment Need was considered as the response variable, and generalized linear models estimated by the GENMOD procedure (release 9.3, 2010; SAS Institute, Cary, NC). Model 1 was estimated with only the intercept, providing the basis for evaluating the reduction in variance in the other models studied; then the variables were tested sequentially, considering P ≤0.05 as the criterion for remaining in the model. Results In the model, self‐perception and self‐esteem were statistically significant in relation to the perceived need for treatment. The normative need was significantly associated with the outcome variable and was not influenced by independent variables. Conclusions The normative need for orthodontics treatment was not overestimated by the perceived need, and the perceived need was not influenced by sex and the impact on quality of life. HighlightsWe studied normative and perceived treatment need with quality of life, self‐esteem, and self‐perception.We examined a population‐based sample of 248 subjects aged 12 years.The normative aspect of orthodontic treatment was assessed by the DHC and the AC of the IOTN.OHRQoL was assessed using the CPQ11‐14, GSE, and OASIS.We used multilevel multiple logistic regression models.Sex and quality of life did not influence childrens perceptions.

Malocclusion in schoolhildren aged 7-12 years old in Minas Gerais, Brazil

Objective The aim of the study was to determine prevalence of malocclusion and the inter- and intra-arch relations in schoolchildren of 7-12 years of Vazante, Minas Gerais, Brazil. Methods In the inter-arch relations the sagittal, vertical and transverse aspects were evaluated, and in the intra-arch relations, diastemas, crowding and tooth losses were determined in 670 children. The maloclussion was classified as Class I , II and III according to Angle, based on the position of the first molars. For this study, the sample was divided into two age groups: children from 7 to 9 years and children from 10 to 12 years old. Results A similar percentage of individuals with Class I and II was found in the two age groups evaluated. A higher percentage of Class III individuals was observed in the age group from 10 to 12 years. The presence of cross bite, anterior open bite, diastemas, crowding and early primary tooth loss was prevalent in the age groups of 7 and 9 years. Deep bite, posterior cross bite and early loss of permanent teeth prevailed in the age from 10 to 12 years. Conclusion It could be concluded that there was a high rate of malocclusion in children and the sagittal relation was maintained in the two periods evaluated. A larger number of manifestations of anterior open bite were observed in the age group of 7 to 9 years, and overbite in the Group from 10 to 12 years. In the transverse relation there was an increase in cross bite from the first to second transitory period.