Andreia Araújo

Influence of the layer thickness in plasmonic gold nanoparticles produced by thermal evaporation

Metallic nanoparticles (NPs) have received recently considerable interest of photonic and photovoltaic communities. In this work, we report the optoelectronic properties of gold NPs (Au-NPs) obtained by depositing very thin gold layers on glass substrates through thermal evaporation electron-beam assisted process. The effect of mass thickness of the layer was evaluated. The polycrystalline Au-NPs, with grain sizes of 14 and 19 nm tend to be elongated in one direction as the mass thickness increase. A 2 nm layer deposited at 250°C led to the formation of Au-NPs with 10-20 nm average size, obtained by SEM images, while for a 5 nm layer the wide size elongates from 25 to 150 nm with a mean at 75 nm. In the near infrared region was observed an absorption enhancement of amorphous silicon films deposited onto the Au-NPs layers with a corresponding increase in the PL peak for the same wavelength region.

Silicon thin film solar cells on commercial tiles

Nanostructured silicon single junction thin film solar cells were deposited on commercial red clay roof tiles with engobe surfaces and earthenware wall tiles with glazed surfaces, with a test area of 24 mm2. We studied the influence of the type of substrate tile, back contact, buffer layer and SiOx passivation layer on the optoelectronic performance of the solar cells. Despite the fact that typical micrometre-sized defects on the surfaces of the tiles and the porous nature of the ceramic substrates make deposition of homogeneous thin films on them quite challenging, we have been able to achieve a cell efficiency of 5% and a quantum efficiency of 80% on non-fully optimized cells on commercial tiles. The method is industrially employable utilizing pre-existing plasma-enhanced chemical vapour deposition technologies. The cost-effectiveness and industrial feasibility of the technique are discussed. Our study shows that photovoltaic tiles can combine energy generation with architectural aesthetics leading to significant implications for advancement in building integrated photovoltaics.

Highly efficient nanoplasmonic SERS on cardboard packaging substrates

This work reports on highly efficient surface enhanced Raman spectroscopy (SERS) constructed on low-cost, fully recyclable and highly reproducible cardboard plates, which are commonly used as disposable packaging material. The active optical component is based on plasmonic silver nanoparticle structures separated from the metal surface of the cardboard by a nanoscale dielectric gap. The SERS response of the silver (Ag) nanoparticles of various shapes and sizes were systematically investigated, and a Raman enhancement factor higher than 106 for rhodamine 6G detection was achieved. The spectral matching of the plasmonic resonance for maximum Raman enhancement with the optimal local electric field enhancement produced by 60 nm-sized Ag NPs predicted by the electromagnetic simulations reinforces the outstanding results achieved. Furthermore, the nanoplasmonic SERS substrate exhibited high reproducibility and stability. The SERS signals showed that the intensity variation was less than 5%, and the SERS performance could be maintained for up to at least 6 months.

Solar cells for self-sustainable intelligent packaging

Nowadays there is a strong demand for intelligent packaging to provide comfort, welfare and security to owners, vendors and consumers by allowing them to know the contents and interact with the goods. This is of particular relevance for low cost, fully disposable and recyclable products, such as identification tags and medical diagnostic tests, and devices for analysis and/or quality control in food and pharmaceutical industries. However, the increase of complexity and processing capacity requires continuous power and can be addressed by the combined use of a small disposable battery, charged by a disposable solar cell, which is able to work under indoor lighting. Herein, we show a proof-of-concept of the pioneering production of thin-film amorphous silicon (a-Si:H) solar cells with an efficiency of 4% by plasma enhanced chemical vapour deposition (PECVD) on liquid packaging cardboard (LPC), which is commonly used in the food and beverage industries. Such accomplishment put us one step closer to this revolution by providing a flexible, renewable and extremely cheap autonomous energy packaging system. Moreover, such Si thin films take advantage of their good performance at low-light levels, which also makes them highly desirable for cheap mobile indoor applications.

Hydrogen plasma treatment of very thin p-type nanocrystalline Si films grown by RF-PECVD in the presence of B(CH3)3

Abstract We have characterized the structure and electrical properties of p-type nanocrystalline silicon films prepared by radio-frequency plasma-enhanced chemical vapor deposition and explored optimization methods of such layers for potential applications in thin-film solar cells. Particular attention was paid to the characterization of very thin (∼20 nm) films. The cross-sectional morphology of the layers was studied by fitting the ellipsometry spectra using a multilayer model. The results suggest that the crystallization process in a high-pressure growth regime is mostly realized through a subsurface mechanism in the absence of the incubation layer at the substrate-film interface. Hydrogen plasma treatment of a 22-nm-thick film improved its electrical properties (conductivity increased more than ten times) owing to hydrogen insertion and Si structure rearrangements throughout the entire thickness of the film.

Office paper decorated with silver nanostars - an alternative cost effective platform for trace analyte detection by SERS

For analytical applications in portable sensors to be used in the point-of-need, low-cost SERS substrates using paper as a base, are an alternative. In this work, SERS substrates were produced on two different types of paper: a high porosity paper (Whatman no. 1); and a low porosity paper (commercially available office paper, Portucel Soporcel). Solutions containing spherical silver nanoparticles (AgNPs) and silver nanostars (AgNSs) were separately drop-casted on hydrophilic wells patterned on the papers. The porosity of the paper was found to play a determinant role on the AgNP and AgNS distribution along the paper fibres, with most of the nanoparticles being retained at the illuminated surface of the office paper substrate. The highest SERS enhancements were obtained for the office paper substrate, with deposited AgNSs. A limit of detection for rhodamine-6G as low as 11.4 ± 0.2 pg could be achieved, with an analytical enhancement factor of ≈107 for this specific analyte. The well patterning technique allowed good signal uniformity (RSD of 1.7%). Besides, these SERS substrates remained stable after 5 weeks of storage (RSD of 7.3%). Paper-induced aggregation of AgNPs was found to be a viable alternative to the classical salt-induced aggregation, to obtain a highly sensitive SERS substrates.

Ag and Sn Nanoparticles to Enhance the Near-Infrared Absorbance of a-Si:H Thin Films

Silver (Ag) and tin (Sn) nanoparticles (NPs) were deposited by thermal evaporation onto heated glass substrates with a good control of size, shape and surface coverage. This process has the advantage of allowing the fabrication of thin-film solar cells with incorporated NPs without vacuum break, since it does not require chemical processes or post-deposition annealing. The X-ray diffraction, TEM and SEM properties are correlated with optical measurements and amorphous silicon hydrogenated (a-Si:H) films deposited on top of both types of NPs show enhanced absorbance in the near-infrared. The results are interpreted with electromagnetic modelling performed with Mie theory. A broad emission in the near-infrared region is considerably increased after covering the Ag nanoparticles with an a-Si:H layer. Such effect may be of interest for possible down-conversion mechanisms in novel photovoltaic devices.

Colloidal-lithographed TiO2 photonic nanostructures for solar cell light trapping

Dielectric-based photonic structures, composed of a lossless but high refractive index material, are currently among the preferential solutions for light management in thin film photovoltaics, as they allow broadband manipulation of sunlight to strongly boost the absorptance in the thin solar cell layers. In this work, we present an innovative colloidal lithography nanofabrication method that allows the precise engineering of wavelength-sized features, with the materials and geometries appropriate for efficient light trapping when implemented on the front surface of the cells. The method is developed here with TiO2 nanostructures tested on amorphous-silicon absorber thin films coated on the rear side by a metallic reflector. It is a simple, low-cost and scalable approach consisting of 4 main steps: (1) deposition of periodic close-packed arrays of polystyrene colloids which act as the mask; (2) shaping the particles and increasing their spacing via dry etching; (3) infiltration of TiO2 into the inter-particle spaces and (4) removal of the polystyrene particles to leave only the structured TiO2 layer. The resultant array of wavelength-sized features acts as a nanostructured high-index anti-reflection coating, which not only suppresses the reflected light at short wavelengths but also increases the optical path length of the longer wavelengths, via light scattering, within the absorber. The optical results have been compared with numerical electromagnetic computations to provide a deeper understanding of the physical mechanisms responsible for absorptance enhancement in the cells. A notorious 27.3% enhancement in the cell photocurrent is anticipated with the fabricated structures, relative to conventional anti-reflection coatings.

Role of a disperse carbon interlayer on the performances of tandem a-Si solar cells

Abstract We report the effect of a disperse carbon interlayer between the n-a-Si:H layer and an aluminium zinc oxide (AZO) back contact on the performance of amorphous silicon solar cells. Carbon was incorporated to the AZO film as revealed by x-ray photoelectron spectroscopy and energy-dispersive x-ray analysis. Solar cells fabricated on glass substrates using AZO in the back contact performed better when a disperse carbon interlayer was present in their structure. They exhibited an initial efficiency of 11%, open-circuit voltage Voc = 1.6 V, short-circuit current JSC = 11 mA cm−2 and a filling factor of 63%, that is, a 10% increase in the JSC and 20% increase in the efficiency compared to a standard solar cell.

Multifunctional cellulose-paper for light harvesting and smart sensing applications

A novel generation of flexible opto-electronic smart applications is now emerging, incorporating photovoltaic and sensing devices driven by the desire to extend and integrate such technologies into a broad range of low cost and disposable consumer products of our everyday life and as a tool to bring together the digital and physical worlds. Several flexible polymeric materials are now under investigation to be used as mechanical supports for such applications. Among them, cellulose, the most abundant organic polymer on the Earth, commonly used in the form of paper, has attracted much research interest due to the advantages of being recyclable, flexible, lightweight, biocompatible and extremely low-cost, when compared to other materials. Cellulose substrates can be found in many forms, from the traditional micro-cellulose paper used for writing, printing and food/beverage packaging (e.g. liquid packaging cardboard), to the nano-cellulose paper which has distinct structural, optical, thermal and mechanical properties that can be tailored to its end use. The present article reviews the state-of-the-art related to the integration and optimization of photonic structures and light harvesting technologies on paper-based platforms, for applications such as Surface Enhanced Raman Scattering (SERS), supporting remarkable 107 signal enhancement, and photovoltaic solar cells reaching ∼5% efficiency, for power supply in standalone applications. Such paper-supported technologies are now possible due to innovative coatings that functionalize the paper surfaces, together with advanced light management solutions (e.g. wave-optical light trapping structures and NIR-to-visible up-converters). These breakthroughs open the way for an innovative class of disposable opto-electronic products that can find widespread use and bring important added value to existing commercial products. By making these devices ubiquitous, flexible and conformable to any object or surface, will also allow them to become part of the core of the Internet of Things (IoT) revolution, which demands systems’ mobility and self-powering functionalities to satisfy the requirements of comfort and healthcare of the users.