Harald Hagendorfer

Potassium-induced surface modification of Cu(In,Ga)Se2 thin films for high-efficiency solar cells

Thin-film photovoltaic devices based on chalcopyrite Cu(In,Ga)Se2 (CIGS) absorber layers show excellent light-to-power conversion efficiencies exceeding 20%. This high performance level requires a small amount of alkaline metals incorporated into the CIGS layer, naturally provided by soda lime glass substrates used for processing of champion devices. The use of flexible substrates requires distinct incorporation of the alkaline metals, and so far mainly Na was believed to be the most favourable element, whereas other alkaline metals have resulted in significantly inferior device performance. Here we present a new sequential post-deposition treatment of the CIGS layer with sodium and potassium fluoride that enables fabrication of flexible photovoltaic devices with a remarkable conversion efficiency due to modified interface properties and mitigation of optical losses in the CdS buffer layer. The described treatment leads to a significant depletion of Cu and Ga concentrations in the CIGS near-surface region and enables a significant thickness reduction of the CdS buffer layer without the commonly observed losses in photovoltaic parameters. Ion exchange processes, well known in other research areas, are proposed as underlying mechanisms responsible for the changes in chemical composition of the deposited CIGS layer and interface properties of the heterojunction.

Behavior of Metallic Silver Nanoparticles in a Pilot Wastewater Treatment Plant

We investigated the behavior of metallic silver nanoparticles (Ag-NP) in a pilot wastewater treatment plant (WWTP) fed with municipal wastewater. The treatment plant consisted of a nonaerated and an aerated tank and a secondary clarifier. The average hydraulic retention time including the secondary clarifier was 1 day and the sludge age was 14 days. Ag-NP were spiked into the nonaerated tank and samples were collected from the aerated tank and from the effluent. Ag concentrations determined by inductively coupled plasma-mass spectrometry (ICP-MS) were in good agreement with predictions based on mass balance considerations. Transmission electron microscopy (TEM) analyses confirmed that nanoscale Ag particles were sorbed to wastewater biosolids, both in the sludge and in the effluent. Freely dispersed nanoscale Ag particles were only observed in the effluent during the initial pulse spike. X-ray absorption spectroscopy (XAS) measurements indicated that most Ag in the sludge and in the effluent was present as Ag(2)S. Results from batch experiments suggested that Ag-NP transformation to Ag(2)S occured in the nonaerated tank within less than 2 h. Physical and chemical transformations of Ag-NP in WWTPs control the fate, the transport and also the toxicity and the bioavailability of Ag-NP and therefore must be considered in future risk assessments.

Release of silver nanoparticles from outdoor facades

In this study we investigate the release of metallic silver nanoparticles (Ag-NP) from paints used for outdoor applications. A facade panel mounted on a model house was exposed to ambient weather conditions over a period of one year. The runoff volume of individual rain events was determined and the silver and titanium concentrations of 36 out of 65 runoff events were measured. Selected samples were prepared for electron microscopic analysis. A strong leaching of the Ag-NP was observed during the initial runoff events with a maximum concentration of 145 micro Ag/l. After a period of one year, more than 30% of the Ag-NP were released to the environment. Particles were mostly <15 nm and are released as composite colloids attached to the organic binders of the paint. Microscopic results indicate that the Ag-NP are likely transformed to considerably less toxic forms such as Ag2S.

Fate and transformation of silver nanoparticles in urban wastewater systems

Discharge of silver nanoparticles (Ag-NP) from textiles and cosmetics, todays major application areas for metallic Ag-NP, into wastewater is inevitable. Transformation and removal processes in sewers and wastewater treatment plants (WWTP) will determine the impact of Ag-NP on aquatic and terrestrial environments, via the effluents of the WWTP and via the use of digested sludge as fertilizer. We thus conducted experiments addressing the behavior of Ag-NP in sewers and in WWTP. We spiked Ag-NP to a 5 km long main trunk sewer and collected 40 wastewater samples after 500 m, 2400 m and 5000 m each according to the expected travel times of the Ag-NP. Excellent mass closure of the Ag derived by multiplying the measured Ag concentrations times the volumetric flow rates indicate an efficient transport of the Ag-NP without substantial losses to the sewer biofilm. Ag-NP reacted with raw wastewater in batch experiments were sulfidized to roughly 15% after 5 h reaction time as revealed by X-ray absorption spectroscopy (XAS). However, acid volatile sulfide (AVS) concentrations were substantially higher in the sewer channel (100 μM) compared to the batch experiments (3 μM; still sufficient to sulfidize spiked 2 μM Ag) possibly resulting in a higher degree of sulfidation in the sewer channel. We further investigated the removal efficiency of 10 nm and 100 nm Ag- and gold (Au)-NP coated with citrate or polyvinylpyrrolidone in activated sludge batch experiments. We obtained very high removal efficiencies (≈ 99%) irrespective of size and coating for Ag- and Au-NP, the latter confirming that the particle type was of minor importance with respect to the degree of NP removal. We observed a strong size dependence of the sulfidation kinetics. We conclude that Ag-NP discharged to the wastewater stream will become sulfidized to various degrees in the sewer system and are efficiently transported to the WWTP. The sulfidation of the Ag-NP will continue in the WWTP, but primarily depending on the size the Ag-NP, may not be complete. Very high removal efficiencies in the WWTP will divert most of the Ag-NP mass flow to the digester and only a small fraction of the Ag will be released to surface waters.

Doping of polycrystalline CdTe for high-efficiency solar cells on flexible metal foil

Roll-to-roll manufacturing of CdTe solar cells on flexible metal foil substrates is one of the most attractive options for low-cost photovoltaic module production. However, various efforts to grow CdTe solar cells on metal foil have resulted in low efficiencies. This is caused by the fact that the conventional device structure must be inverted, which imposes severe restrictions on device processing and consequently limits the electronic quality of the CdTe layer. Here we introduce an innovative concept for the controlled doping of the CdTe layer in the inverted device structure by means of evaporation of sub-monolayer amounts of Cu and subsequent annealing, which enables breakthrough efficiencies up to 13.6%. For the first time, CdTe solar cells on metal foil exceed the 10% efficiency threshold for industrialization. The controlled doping of CdTe with Cu leads to increased hole density, enhanced carrier lifetime and improved carrier collection in the solar cell. Our results offer new research directions for solving persistent challenges of CdTe photovoltaics.

Highly transparent and conductive ZnO: Al thin films from a low temperature aqueous solution approach.

A solution deposition approach for high-performance aluminum-doped zinc oxide (AZO) thin films (visible transparency > 90% and sheet resistance down to 25 Ω/sq) with process temperatures not exceeding 85 °C is presented. This allows the non-vacuum deposition of AZO on temperature sensitive substrates such as polymer films for flexible and transparent electronics, or inorganic and organic thin film photovoltaics.

Alkali-templated surface nanopatterning of chalcogenide thin films: a novel approach toward solar cells with enhanced efficiency.

Concepts of localized contacts and junctions through surface passivation layers are already advantageously applied in Si wafer-based photovoltaic technologies. For Cu(In,Ga)Se2 thin film solar cells, such concepts are generally not applied, especially at the heterojunction, because of the lack of a simple method yielding features with the required size and distribution. Here, we show a novel, innovative surface nanopatterning approach to form homogeneously distributed nanostructures (<30 nm) on the faceted, rough surface of polycrystalline chalcogenide thin films. The method, based on selective dissolution of self-assembled and well-defined alkali condensates in water, opens up new research opportunities toward development of thin film solar cells with enhanced efficiency.

UV-protection of wood surfaces by controlled morphology fine-tuning of ZnO nanostructures

Abstract One of the most significant limitations for a wider utilisation of the renewable and CO2-storing resource wood is its low ultraviolet (UV) light stability. The protection of the wood surface without altering its aesthetic appeal requires an optically transparent but UV protective coating which should be strongly attached to the rough and inhomogeneous substrate. For this purpose, ZnO nanostructures were deposited onto the wood surface via a chemical bath deposition process. The morphology of crystalline ZnO was controlled by aluminium nitrate or ammonium citrate in the growth step resulting in nanorod arrays or platelet structures, respectively. Detailed structural, chemical and mechanical characterisations as well as accelerated weathering exposure revealed the effective performance of the platelet structure, which formed a dense and thin ZnO coating on spruce. The total colour change (ΔE in the CIE system) was calculated to be 20.5 for unmodified wood, while it was about three for the modified samples after 4 weeks accelerated weathering test. Moreover, the ZnO coating also suppressed crack initiation and propagation indicating a substantial increase in durability.

A straightforward wet-chemistry method for the determination of solid and gaseous mercury fractions in Backlight Cold Cathode Fluorescence Lamps

Backlight Cold Cathode Fluorescence Lamps (B-CCFLs) are already applied in many electronic consumer products such as LCD screens, flat screen TVs, and laptop monitors. In consequence, an increase of such products entering the waste streams can be expected in the near future. As a result of the mercury (Hg) employed in such lamps, the development of recycling techniques to create a best practical environmental option for appropriate end-of-life strategies are necessary. For this purpose the knowledge about speciation in terms of solid and gaseous state of Hg in such lamps is inevitable. However, analytical techniques to discriminate solid and gaseous Hg require a special setup, not available in most routine laboratories. Thus a straightforward and cost efficient analytical technique is of need. In this work we describe sample preparation procedures and analysis techniques, which only require equipment already available in most routine laboratories. The volatile fraction is extracted with a KMnO(4) solution utilizing a novel approach, taking the advantage that the B-CCFL glass tubes have a negative pressure. Thus the extraction solution is directly sucked into the tube where the volatile Hg-fraction is immediately extracted. Subsequently, the solid fraction is dissolved via microwave assisted pressure acid digestion after cryo-milling. Analysis for both fractions took place employing a cold vapor atomic absorption system. To prove the new method is fit for purpose, spiking experiments and analysis of reference materials (when available) was performed with recoveries being between 90% and 110%. First results obtained for a stack of lamps from an used LCD-TV display reveal that solid Hg fractions in all lamps show a variation of 20% between samples whereas the gaseous Hg content can vary up to 600%.

Indium-Free PTB7/PC71BM Polymer Solar Cells with Solution-Processed Al:ZnO Electrodes on PET Substrates

Inverted PTB7/PC71BM polymer solar cells are prepared on solution-processed Al:ZnO transparent contacts on PET substrates. Al:ZnO is deposited by a low temperature chemical bath deposition route (T < 100°C at any step) to comply with the temperature sensitive substrate. A maximum conversion efficiency of 6.4% and 6.9% is achieved for the indium-free solar cells on PET and glass substrates, respectively. The devices are relatively stable in air whereby an initial efficiency loss in the order of 15% after storage for 15 days can be fully recovered by light soaking.