Peter Biolsi

Self-aligned quadruple patterning integration using spacer on spacer pitch splitting at the resist level for sub-32nm pitch applications

Multiple patterning integrations for sub 193nm lithographic resolution are becoming increasingly creative in pursuit of cost reduction and achieving desired critical dimension. Implementing these schemes into production can be a challenge. Aimed at reducing cost associated with multiple patterning for the 10nm node and beyond, we will present a self-aligned quadruple patterning strategy which uses 193nm immersion lithography resist pattern as a first mandrel and a spacer on spacer integration to enable a final pitch of 30nm. This option could be implemented for front end or back end critical layers such as Fin and Mx. Investigation of combinations of low temperature ALD films such as TiO, Al2O3 and SiO2 will be reviewed to determine the best candidates to meet the required selectivities, LER/LWR and CDs.

Challenges and mitigation strategies for resist trim etch in resist-mandrel based SAQP integration scheme

Patterning the desired narrow pitch at 10nm technology node and beyond, necessitates employment of either extreme ultra violet (EUV) lithography or multi-patterning solutions based on 193nm-immersion lithography. With enormous challenges being faced in getting EUV lithography ready for production, multi-patterning solutions that leverage the already installed base of 193nm-immersion-lithography are poised to become the industry norm for 10 and 7nm technology nodes. For patterning sub-40nm pitch line/space features, self-aligned quadruple patterning (SAQP) with resist pattern as the first mandrel shows significant cost as well as design benefit, as compared to EUV lithography or other multi-patterning techniques. One of the most critical steps in this patterning scheme is the resist mandrel definition step which involves trimming / reformation of resist profile via plasma etch for achieving appropriate pitch after the final pattern. Being the first mandrel, the requirements for the Line Edge Roughness (LER) / Line Width Roughness (LWR); critical dimension uniformity (CDU); and profile in 3-dimensions for the resist trim / reformation etch is extremely aggressive. In this paper we highlight the unique challenges associated in developing resist trim / reformation plasma etch process for SAQP integration scheme and summarize our efforts in optimizing the trim etch chemistries, process steps and plasma etch parameters for meeting the mandrel definition targets. Finally, we have shown successful patterning of 30nm pitch patterns via the resist-mandrel SAQP scheme and its implementation for Si-fin formation at 7nm node.

EPE improvement thru self-alignment via multi-color material integration

As the industry marches on onto the 5nm node and beyond, scaling has slowed down, with all major IDMs & foundries predicting a 3-4 year cadence for scaling. A major reason for this slowdown is not the technical challenge of making features smaller, but effective control of variation that creeps in to the fabrication process. That variability manifests itself as edge placement error (EPE), which has a direct impact on wafer yield. Simply defined as the variance between design intent vs. actual on-wafer results, EPE is one of the foremost challenges being faced by the industry at the advanced node for both logic and memory. This is especially critical at three stages: the front end of line (FEOL) STI patterning; middle of line (MOL) contact patterning; and back end of line (BEOL) trench patterning where the desired tight pitch demands EPE control beyond the capability of 193i multi-patterning or even EUV single pattern. In order to mitigate this EPE challenge, we are proposing self-alignment of blocks & cuts through a multi-color materials integration concept. This approach, termed as “Self-aligned block or Cut (SAB or SACut)”, simply trades off the un-manageable overlay requirement into a more manageable etch selectivity challenge, by having multiple materials filled in every other trench or line. In this paper we will introduce self-alignment based block and cut strategies using multi-color materials integration and show implementation for BEOL trench block patterning. We will present a breakdown of the key unit process challenges that were needed to be resolved for enabling the self-alignment such as: (a) material selection of multi-color approach; (b) planarization of spin on materials; (c) void-free gap fill for high aspect ratio features; and last but not the least, (c) etch selectivity of etching one material with respect to all other materials exposed. Further, we will present a comparison of our new self-alignment approach with standard approaches where we will articulate the advantages in terms of EPE relaxation and mask number reduction. We will conclude our talk with a brief snapshot of the future direction of our EPE improvement strategies and our view on the future of patterning beyond 5nm node for the industry.

LER improvement for sub-32nm pitch self-aligned quadruple patterning (SAQP) at back end of line (BEOL)

Critical back end of line (BEOL) Mx patterning at 7nm technology node and beyond requires sub-36nm pitch line/space pattern in order to meet the scaling requirements. This small pitch can be achieved by either extreme ultraviolet (EUV) lithography or 193nm-immersion-lithography based self-aligned quadruple patterning (SAQP). With enormous challenges being faced in production readiness of EUV lithography, SAQP is expected to be the front up approach for Mx grid patterning for most of industry. In contrast to the front end of line (FEOL) fin patterning, which has successfully deployed SAQP approach since 10nm node technology, BEOL Mx SAQP is challenging owing to the required usage of significantly lower temperature budgets for film stack deposition. This has an adverse impact on the material properties of the as-deposited films leading to emergence of several challenges for etch including selectivity, uniformity and roughness. In this presentation we will highlight those unique etch challenges associated with our BEOL Mx SAQP patterning strategy and summarize our efforts in optimizing the patterning stack, etch chemistries & process steps for meeting the 7nm technology node targets. We will present comparison data on both organic and in-organic mandrel stacks with respect to LER/LWR & CDU. With LER being one of the most critical targets for 7nm BEOL Mx, we will outline our actions for optimization of our stack including resist material, mandrel material, spacer material and others. Finally, we would like to update our progress on achieving the target LER of 1.5 nm for 32nm pitch BEOL SAQP pattern.

Multi-color approach on self-aligned multiple patterning for single line cut application

Over the past few decades, the semiconductor industry has been employing size shrinkage as the most efficient method to reduce production cost in order to fit more and more transistors on one unit area. Each size shrinkage has been categorized as either node or generation by the theoretical gate length of Metal-Oxide-Semiconductor Field-Effect Transistor (MOSFET). In the advanced node, such as the sub-10nm node, size shrinkage is not applicable due to the physics limitation of 193nm immersion lithography. Therefore, alternative methods, extreme ultra violet lithography (EUV) and multi-patterning solutions based on 193nm immersion lithography, are attracting significant attentions in research and development across the industry. Among the various patterning techniques, the front-runner is self-aligned multiple patterning (SAMP). This technique uses the sidewall spacer formation as a transferable pattern and achieve pitch halving purpose. By repeating this technique, the pitch halving can be executed countless times, theoretically; this gives this technique an advantage over other techniques. However, due to the device design and sidewall formation in both sides, an additional line cut step is required to be performed to fulfill the requirements of isolation and N/P boundaries. The most challenging pattern in the line cut step is the single line cut without defect formation.

Multi-color fly-cut-SAQP for reduced process variation

Multi-patterning processes such as self-aligned double patterning (SADP) and self-aligned quadruple patterning (SAQP) present new challenges to the semiconductor device manufacturing such as increased relative cost to previous nodes, longer cycle times, and increased (local) edge placement error between grid and cut/block layers. As the scaling requirements continue, the factors driving both EPE and electrical yield such as overlay, critical dimension control (CDU) and stochastics (LCDU) become greater concerns to multi-patterning. In addition to lithographic process variations, the unit processes such as plasma/vapor etch, deposition, wet/cleans can contributes additional variation in spacer/mandrel profiles leading to poor CDU control and ultimately within-wafer pitch walking. In this paper, we outline alternative SAQP integration schemes to improve the feature profile of both mandrel and spacer to minimize process variability. This patterning scheme designated as fly-cut SAQP introduces new concepts such top spacer removal by chemical-mechanical planarization, mandrel foot mitigation layers, multi-layered mandrel for accurate polish end-point and void-free gap fill to realize high fidelity transfer to the underlying hardmask. Finally, we will demonstrate the effectiveness for this new integration scheme as a candidate for multi-color/self-aligned block (SAB) and highlight the additional benefits of using such an approach.

Self-aligned blocking integration demonstration for critical sub-30nm pitch Mx level patterning with EUV self-aligned double patterning

We report a sub-30nm pitch self-aligned double patterning (SADP) integration scheme with EUV lithography coupled with self-aligned block technology (SAB) targeting the back end of line (BEOL) metal line patterning applications for logic nodes beyond 5nm. The integration demonstration is a validation of the scalability of a previously reported flow, which used 193nm immersion SADP targeting a 40nm pitch with the same material sets (Si3N4 mandrel, SiO2 spacer, Spin on carbon, spin on glass). The multi-color integration approach is successfully demonstrated and provides a valuable method to address overlay concerns and more generally edge placement error (EPE) as a whole for advanced process nodes. Unbiased LER/LWR analysis comparison between EUV SADP and 193nm immersion SADP shows that both integrations follow the same trend throughout the process steps. While EUV SADP shows increased LER after mandrel pull, metal hardmask open and dielectric etch compared to 193nm immersion SADP, the final process performance is matched in terms of LWR (1.08nm 3 sigma unbiased) and is only 6% higher than 193nm immersion SADP for average unbiased LER. Using EUV SADP enables almost doubling the line density while keeping most of the remaining processes and films unchanged, and provides a compelling alternative to other multipatterning integrations, which present their own sets of challenges.

EUV patterning using CAR or MOX photoresist at low dose exposure for sub 36nm pitch

The semiconductor industry has been pushing the limits of scalability by combining 193nm immersion lithography with multi-patterning techniques for several years. Those integrations have been declined in a wide variety of options to lower their cost but retain their inherent variability and process complexity. EUV lithography offers a much desired path that allows for direct print of line and space at 36nm pitch and below and effectively addresses issues like cycle time, intra-level overlay and mask count costs associated with multi-patterning. However it also brings its own sets of challenges. One of the major barrier to high volume manufacturing implementation has been hitting the 250W power exposure required for adequate throughput [1]. Enabling patterning using a lower dose resist could help move us closer to the HVM throughput targets assuming required performance for roughness and pattern transfer can be met. As plasma etching is known to reduce line edge roughness on 193nm lithography printed features [2], we investigate in this paper the level of roughness that can be achieved on EUV photoresist exposed at a lower dose through etch process optimization into a typical back end of line film stack. We will study 16nm lines printed at 32 and 34nm pitch. MOX and CAR photoresist performance will be compared. We will review step by step etch chemistry development to reach adequate selectivity and roughness reduction to successfully pattern the target layer.

Selective dry etching of silicon containing anti-reflective coating

Multi-layer patterning schemes involve the use of Silicon containing Anti-Reflective Coating (SiARC) films for their anti-reflective properties. Patterning transfer completion requires complete and selective removal of SiARC which is very difficult due to its high silicon content (>40%). Typically, SiARC removal is accomplished through a non-selective etch during the pattern transfer process using fluorine containing plasmas, or an ex-situ wet etch process using hydrofluoric acid is employed to remove the residual SiARC, post pattern transfer. Using a non-selective etch may result in profile distortion or wiggling, due to distortion of the underlying organic layer. The drawbacks of using wet etch process for SiARC removal are increased overall processing time and the need for additional equipment. Many applications may involve patterning of active structures in a poly-Si layer with an underlying oxide stopping layer. In such applications, SiARC removal selective to oxide using a wet process may prove futile. Removing SiARC selectively to SiO2 using a dry etch process is also challenging, due to similarity in the nature of chemical bonds (Si – O) in the two materials. In this work, we present highly selective etching of SiARC, in a plasma driven by a surface wave radial line slot antenna. The first step in the process involves an in-situ modification of the SiARC layer in O2 plasma followed by selective etching in a NF3/H2 plasma. Surface treatment in O2 plasma resulted in enhanced etching of the SiARC layer. For the right processing conditions, in-situ NF3/H2 dry etch process demonstrated selectivity values greater than 15:1 with respect to SiO2. The etching chemistry, however, was sensitive to NF3:H2 gas ratio. For dilute NF3 in H2, no SiARC etching was observed. Presumably, this is due to the deposition of ammonium fluorosilicate layer that occurs for dilute NF3/H2 plasmas. Additionally, challenges involved in selective SiARC removal (selective to SiO2, organic and Si layers) post pattern transfer, in a multi-layer structure will be discussed.

Line roughness improvements on self-aligned quadruple patterning by wafer stress engineering

In integrated circuit and memory devices, size shrinkage has been the most effective method to reduce production cost and enable the steady increment of the number of transistors per unit area over the past few decades. In order to reduce the die size and feature size, it is necessary to minimize pattern formation in the advance node development. In the node of sub-10nm, extreme ultra violet lithography (EUV) and multi-patterning solutions based on 193nm immersionlithography are the two most common options to achieve the size requirement. In such small features of line and space pattern, line width roughness (LWR) and line edge roughness (LER) contribute significant amount of process variation that impacts both physical and electrical performances. In this paper, we focus on optimizing the line roughness performance by using wafer stress engineering on 30nm pitch line and space pattern. This pattern is generated by a self-aligned quadruple patterning (SAQP) technique for the potential application of fin formation. Our investigation starts by comparing film materials and stress levels in various processing steps and material selection on SAQP integration scheme. From the cross-matrix comparison, we are able to determine the best stack of film selection and stress combination in order to achieve the lowest line roughness performance while obtaining pattern validity after fin etch. This stack is also used to study the step-by-step line roughness performance from SAQP to fin etch. Finally, we will show a successful patterning of 30nm pitch line and space pattern SAQP scheme with 1nm line roughness performance.