E.M. Hollmann

Transport by intermittent convection in the boundary of the DIII-D tokamak

Intermittent plasma objects (IPOs) featuring higher pressure than the surrounding plasma, and responsible for ∼50% of the E×BT radial transport, are observed in the scrape off layer (SOL) and edge of the DIII-D tokamak [J. Watkins et al., Rev. Sci. Instrum. 63, 4728 (1992)]. Conditional averaging reveals that the IPOs, produced at a rate of ∼3×103 s−1, are positively charged and also polarized, featuring poloidal electric fields of up to 4000 V/m. The IPOs move poloidally at speeds of up to 5000 m/s and radially with E×BT/B2 velocities of ∼2600 m/s near the last closed flux surface (LCFS), and ∼330 m/s near the wall. The IPOs slow down as they shrink in radial size from 4 cm at the LCFS to 0.5 cm near the wall. The IPOs appear in the SOL of both L and H mode discharges and are responsible for nearly 50% of the SOL radial E×B transport at all radii; however, they are highly reduced in absolute amplitude in H-mode conditions.

Transport by intermittency in the boundary of the DIII-D tokamak

A271 TRANSPORT BY INTERMITTENCY IN THE BOUNDARY OF THE DIII-D TOKAMAK. Intermittent plasma objectives (IPOs) featuring higher pressure than the surrounding plasma, are responsible for {approx} 50% of the E x B{sub T} radial transport in the scrape off layer (SOL) of the DIII-D tokamak in L- and H-mode discharges. Conditional averaging reveals that the IPOs are positively charged and feature internal poloidal electric fields of up to 4000 V/m. The IPOs move radially with E x B{sub T}/B{sup 2} velocities of {approx} 2600 m/s near the last closed flux surface (LCFS), and {approx} 330 m/s near the wall. The IPOs slow down as they shrink in radial size from 4 cm at the LCFS to 0.5 cm near the wall. The skewness (i.e. asymmetry of fluctuations from the average) of probe and beam emission spectroscopy (BES) data indicate IPO formation at or near the LCFS and the existence of positive and negative IPOs which move in opposite directions. The particle content of the IPOs at the LCFS is linearly dependent on the local density and decays over {approx} 3 cm into the SOL while their temperature decays much faster ({approx} 1 cm).

Dust measurements in tokamaks (invited)

Dust production and accumulation present potential safety and operational issues for the ITER. Dust diagnostics can be divided into two groups: diagnostics of dust on surfaces and diagnostics of dust in plasma. Diagnostics from both groups are employed in contemporary tokamaks; new diagnostics suitable for ITER are also being developed and tested. Dust accumulation in ITER is likely to occur in hidden areas, e.g., between tiles and under divertor baffles. A novel electrostatic dust detector for monitoring dust in these regions has been developed and tested at PPPL. In the DIII-D tokamak dust diagnostics include Mie scattering from Nd:YAG lasers, visible imaging, and spectroscopy. Laser scattering is able to resolve particles between 0.16 and 1.6 microm in diameter; using these data the total dust content in the edge plasmas and trends in the dust production rates within this size range have been established. Individual dust particles are observed by visible imaging using fast framing cameras, detecting dust particles of a few microns in diameter and larger. Dust velocities and trajectories can be determined in two-dimension with a single camera or three-dimension using multiple cameras, but determination of particle size is challenging. In order to calibrate diagnostics and benchmark dust dynamics modeling, precharacterized carbon dust has been injected into the lower divertor of DIII-D. Injected dust is seen by cameras, and spectroscopic diagnostics observe an increase in carbon line (CI, CII, C(2) dimer) and thermal continuum emissions from the injected dust. The latter observation can be used in the design of novel dust survey diagnostics.

Far SOL transport and main wall plasma interaction in DIII-D

Far Scrape-Off Layer (SOL) and near-wall plasma parameters in DIII-D depend strongly on the discharge parameters and confinement regime. In L-mode discharges cross-field transport increases with the average discharge density and flattens far SOL profiles, thus increasing plasma contact with the low field side (LFS) main chamber wall. In H-mode between edge localized modes (ELMs) the plasma?wall contact is weaker than in L-mode. During ELM fluxes of particles and heat to the LFS wall increase transiently above the L-mode values. Depending on the discharge conditions, ELMs are responsible for 30?90% of the net ion flux to the outboard chamber wall. ELMs in high density discharges feature intermittent transport events similar to those observed in L-mode and attributed to blobs of dense hot plasma formed inside the separatrix and propagating radially outwards. Though the blobs decay with radius, some of them survive long enough to reach the outer wall and possibly cause sputtering. In lower density H-modes, ELMs can feature blobs of pedestal density propagating all the way to the outer wall.

Status of research toward the ITER disruption mitigation system

An overview of the present status of research toward the final design of the ITER disruption mitigation system (DMS) is given. The ITER DMS is based on massive injection of impurities, in order to radiate the plasma stored energy and mitigate the potentially damaging effects of disruptions. The design of this system will be extremely challenging due to many physics and engineering constraints such as limitations on port access and the amount and species of injected impurities. Additionally, many physics questions relevant to the design of the ITER disruption mitigation system remain unsolved such as the mechanisms for mixing and assimilation of injected impurities during the rapid shutdown and the mechanisms for the subsequent formation and dissipation of runaway electron current.

Measurements of impurity and heat dynamics during noble gas jet-initiated fast plasma shutdown for disruption mitigation in DIII-D

Impurity deposition and mixing during gas jet-initiated plasma shutdown is studied using a rapid ({approx}2 ms), massive ({approx}10{sup 22} particles) injection of neon or argon into stationary DIII-D H-mode discharges. Fast-gated camera images indicate that the bulk of the jet neutrals do not penetrate far into the plasma pedestal. Nevertheless, high ({approx}90%) thermal quench radiated power fractions are achieved; this appears to be facilitated through a combination of fast ion mixing and fast heat transport, both driven by large-scale MHD activity. Also, runaway electron suppression is achieved for sufficiently high gas jet pressures. These experiments suggest that massive gas injection could be viable for disruption mitigation in future tokamaks even if core penetration of jet neutrals is not achieved.

Measurement and Modeling of Molecular Ion Concentrations in a Hydrogen Reflex-arc Discharge

The concentrations of the ions H+, H2+, and H3+ are measured in a weakly-ionized hydrogen plasma with electron temperatures Te=3–7 eV, electron densities Ne=1011–1012 cm−3, and background gas densities NH2=5×1013–1015 cm−3. The relative ion concentrations are measured using an omegatron-type mass spectrometer, while the electron density and temperature are measured using a Langmuir probe together with absolutely-calibrated Hα emission spectroscopy. The mean lifetime of ions in the plasma is estimated from fixed wall probe measurements. From the measured parameters, the expected steady-state molecular ion concentrations are modeled using the relevant rate balance equations. It is found that the observed molecular ion concentrations can be predicted within the experimental accuracy using currently available collision cross sections.

Control and dissipation of runaway electron beams created during rapid shutdown experiments in DIII-D

DIII-D experiments on rapid shutdown runaway electron (RE) beams have improved the understanding of the processes involved in RE beam control and dissipation. Improvements in RE beam feedback control have enabled stable confinement of RE beams out to the volt-second limit of the ohmic coil, as well as enabling a ramp down to zero current. Spectroscopic studies of the RE beam have shown that neutrals tend to be excluded from the RE beam centre. Measurements of the RE energy distribution function indicate a broad distribution with mean energy of order several MeV and peak energies of order 30?40?MeV. The distribution function appears more skewed towards low energies than expected from avalanche theory. The RE pitch angle appears fairly directed (????0.2) at high energies and more isotropic at lower energies (??<?100?keV). Collisional dissipation of RE beam current has been studied by massive gas injection of different impurities into RE beams; the equilibrium assimilation of these injected impurities appears to be reasonably well described by radial pressure balance between neutrals and ions. RE current dissipation following massive impurity injection is shown to be more rapid than expected from avalanche theory?this anomalous dissipation may be linked to enhanced radial diffusion caused by the significant quantity of high-Z impurities (typically argon) in the plasma. The final loss of RE beams to the wall has been studied: it was found that conversion of magnetic to kinetic energy is small for RE loss times smaller than the background plasma ohmic decay time of order 1?2?ms.

Gas jet disruption mitigation studies on Alcator C-Mod and DIII-D

High-pressure noble gas jet injection is a mitigation technique which potentially satisfies the requirements of fast response time and reliability, without degrading subsequent discharges. Previously reported gas jet experiments on DIII-D showed good success at reducing deleterious disruption effects. In this paper, results of recent gas jet disruption mitigation experiments on Alcator C-Mod and DIII-D are reported. Jointly, these experiments have greatly improved the understanding of gas jet dynamics and the processes involved in mitigating disruption effects. In both machines, the sequence of events following gas injection is observed to be quite similar: the jet neutrals stop near the plasma edge, the edge temperature collapses and large MHD modes are quickly destabilized, mixing the hot plasma core with the edge impurity ions and radiating away the plasma thermal energy. High radiated power fractions are achieved, thus reducing the conducted heat loads to the chamber walls and divertor. A significant (2 × or more) reduction in halo current is also observed. Runaway electron generation is small or absent. These similar results in two quite different tokamaks are encouraging for the applicability of this disruption mitigation technique to ITER.

Dust studies in DIII-D and TEXTOR

Studies of naturally occurring and artificially introduced carbon dust are conducted in DIII-D and TEXTOR. In DIII-D, dust does not present operational concerns except immediately after entry vents. Submicrometre sized dust is routinely observed using Mie scattering from a Nd : Yag laser. The source is strongly correlated with the presence of type I edge localized modes (ELMs). Larger size (0.005–1 mm diameter) dust is observed by optical imaging, showing elevated dust levels after entry vents. Inverse dependence of the dust velocity on the inferred dust size is found from the imaging data. Heating of the dust particles by the neutral beam injection (NBI) and acceleration of dust particles by the plasma flows are observed. Energetic plasma disruptions produce significant amounts of dust; on the other hand, large flakes or debris falling into the plasma may induce a disruption. Migration of pre-characterized carbon dust is studied in DIII-D and TEXTOR by introducing micrometre-size particles into plasma discharges. In DIII-D, a sample holder filled with 30–40 mg of dust is inserted in the lower divertor and exposed, via sweeping of the strike points, to the diverted plasma flux of high-power ELMing H-mode discharges. After a brief dwell (~0.1 s) of the outer strike point on the sample holder, part of the dust penetrates into the core plasma, raising the core carbon density by a factor of 2–3 and resulting in a twofold increase in the radiated power. In TEXTOR, instrumented dust holders with 1–45 mg of dust are exposed in the scrape-off-layer 0–2 cm radially outside of the last closed flux surface in discharges heated with 1.4 MW of NBI. Launched in this configuration, the dust perturbed the edge plasma, as evidenced by a moderate increase in the edge carbon content, but did not penetrate into the core plasma.