Yunpeng Yin

Integration of EUV lithography in the fabrication of 22-nm node devices

On the road to insertion of extreme ultraviolet (EUV) lithography into production at the 16 nm technology node and below, we are testing its integration into standard semiconductor process flows for 22 nm node devices. In this paper, we describe the patterning of two levels of a 22 nm node test chip using single-exposure EUV lithography; the other layers of the test chip were patterned using 193 nm immersion lithography. We designed a full-field EUV mask for contact and first interconnect levels using rule-based corrections to compensate for the EUV specific effects of mask shadowing and imaging system flare. The resulting mask and the 0.25-NA EUV scanner utilized for the EUV lithography steps were found to provide more than adequate patterning performance for the 22 nm node devices. The CD uniformity across the exposure field and through a lot of wafers was approximately 6.1% (3σ) and the measured overlay on a representative test chip wafer was 13.0 nm (x) and 12.2 nm (y). A trilayer resist process that provided ample process latitude and sufficient etch selectivity for pattern transfer was utilized to pattern the contact and first interconnect levels. The etch recipes provided good CD control, profiles and end-point discrimination. The patterned integration wafers have been processed through metal deposition and polish at the contact level and are now being patterned at the first interconnect level.

Insertion strategy for EUV lithography

The first use of extreme ultraviolet (EUV) lithography in logic manufacturing is targeted for the 14 nm node, with possible earlier application to 20-nm node logic device back-end layers to demonstrate the technology. Use of EUV lithography to pattern the via-levels will allow the use of dark-field EUV masks with low pattern densities and will postpone the day when completely defect-free EUV mask blanks are needed. The quality of the imaging at the 14 nm node with EUV lithography is considerably higher than with double-dipole or double-exposure double-etch 193-nm immersion lithography, particularly for 2-dimensional patterns such as vias, because the Rayleigh k1-value when printing with 0.25 numerical aperture (NA) EUV lithography is so much higher than with 1.35 NA 193-nm immersion lithography and the process windows with EUV lithography are huge. In this paper, the status of EUV lithography technology as seen from an end-user perspective is summarized and the current values of the most important metrics for each of the critical elements of the technology are compared to the values needed for the insertion of EUVL into production at the 14 nm technology node.

EUV lithography at the 22nm technology node

We are evaluating the readiness of extreme ultraviolet (EUV) lithography for insertion into production at the 15 nm technology node by integrating it into standard semiconductor process flows because we believe that device integration exercises provide the truest test of technology readiness and, at the same time, highlight the remaining critical issues. In this paper, we describe the use of EUV lithography with the 0.25 NA Alpha Demo Tool (ADT) to pattern the contact and first interconnect levels of a large (~24 mm x 32 mm) 22 nm node test chip using EUV masks with state-of-the-art defectivity (~0.3 defects/cm2). We have found that: 1) the quality of EUVL printing at the 22 nm node is considerably higher than the printing produced with 193 nm immersion lithography; 2) printing at the 22 nm node with EUV lithography results in higher yield than double exposure double-etch 193i lithography; and 3) EUV lithography with the 0.25 NA ADT is capable of supporting some early device development work at the 15 nm technology node.

Directed self-assembly process implementation in a 300mm pilot line environment

The patterning capability of the directed self-assembly (DSA) of a 42nm-pitch block copolymer on an 84nm-pitch guiding pattern was investigated in a 300mm pilot line environment. The chemoepitaxy guiding pattern was created by the IBM Almaden approach using brush materials in combination with an optional chemical slimming of the resist lines. Critical dimension (CD) uniformity, line-edge/line-width roughness (LER/LWR), and lithographic process window (PW) of the DSA process were characterized. CD rectification and LWR reduction were observed. The chemical slimming process was found to be effective in reducing pattern collapse, hence, slightly improving the DSA PW under over-dose conditions. However, the overall PW was found to be smaller than without using the slimming, due to a new failure mode at under-dose region.

64 nm pitch Cu dual-damascene interconnects using pitch split double exposure patterning scheme

This work demonstrates the building of 64 nm pitch copper single and dual damascene interconnects using pitch split double patterning scheme to enable sub 80nm pitch patterning. A self-aligned-via (SAV) litho/RIE scheme was used to create vias confined by line trenches such that via to line spacing is maximized for better reliability. An undercut free post RIE trench profile enabled the good metal fill. Initial reliability test result and the possibility of using the same scheme for 56 nm pitch interconnects are also discussed.

Optimization of pitch-split double patterning phoresist for applications at the 16nm node

Pitch-split resist materials have been developed for the fabrication of sub-74 nm pitch semiconductor devices. A thermal cure method is used to enable patterning of a second layer of resist over the initially formed layer. Process window, critical dimension uniformity, defectivity and integration with fabricator applications have been explored. A tone inversion process has been developed to enable the application of pitch split to dark field applications in addition to standard bright field applications.

48nm Pitch cu dual-damascene interconnects using self aligned double patterning scheme

For sub-64nm pitch interconnects build, it is beneficial to use Self Aligned Double Patterning (SADP) scheme for line level patterning. Usually a 2X pitch pattern was printed first, followed by a Sidewall Image Transfer (SIT) technique to create the 1X pitch pattern. A block lithography process is then used to trim this pattern to form the actual designed pattern. In this paper, 48nm and 45nm pitch SADP build will be used as examples to demonstrate the SADP patterning scheme. General discussions about this patterning scheme will be provided including: 1) the process flow of this technique, 2) benefits of the technique vs. pitch split approach, 3) the design impact and limitation, and 4) the extendability to smaller line pitch build.

56 nm pitch copper dual-damascene interconnects with triple pitch split metal and double pitch split via

This work demonstrates the building of a 56 nm pitch copper dual damascene interconnects which connects to the local interconnect level. This M1/V0 dual-damascene used a triple pitch split bi-directional M1 and a double pitch split contact (V0) scheme where the local interconnects are with double pitch split in each direction, respectively. This scheme will provide great design flexibility for the advanced logic circuits. The patterning scheme is multiple negative tone development lithography-etch. A memorization layer is utilized in the triple patterned M1 and the double patterned V0 levels, respectively. After transferring the two via levels into the metal memorization layer, a self-aligned-via (SAV) RIE scheme was used to create vias confined by line trenches such that via to line spacing is maximized for better reliability. Seven litho/etch steps (LIP1/LIP2/V0C1/V0C2/M1P1/M1P2/M1P3) were employed to present this revolutionary interconnects.

Robust self-aligned via process for 64nm pitch Dual-Damascene interconnects using pitch split double exposure patterning scheme

A self-aligned via(SAV) process was employed to build 64nm pitch Dual-Damascene(DD) interconnects using a pitch split double exposure pattering scheme to form the Cu lines. TiN hardmask (HM) density and thickness were optimized to achieve the SAV process and DD structure build. We present STEM cross sections of the structures after TiN HM deposition, HM open and DD RIE to determine the minimum required TiN HM thickness for the SAV process. We characterized the TiN loss for each RIE step from cross section results and defined the optimal TiN thickness for 64nm pitch interconnects. Using the optimized TiN thickness, we fabricated DD structures and compared the metal-to-via short electrical performance for SAV and non-SAV processes to show the overlay (OL) impact on shorts yield. Structures fabricated using the SAV process have excellent yield regardless of the degree of via misalignment in the SAV direction since no via CD growth occurs in the constrained SAV direction, while those processed with a non-SAV scheme show via yield degradation with increasing via misalignment. Also, with respect to misalignment in the non-SAV direction, there were no significant electrical differences between structures made using SAV and non-SAV approaches.

Overcoming the challenges of 22-nm node patterning through litho-design co-optimization

Historically, lithographic scaling was driven by both improvements in wavelength and numerical aperture. Recently, the semiconductor industry completed the transition to 1.35NA immersion lithography. The industry is now focusing on double patterning techniques (DPT) as a means to circumvent the limitations of Rayleigh diffraction. Here, the IBM Alliance demonstrates the extendibility of several double patterning solutions that enable scaling of logic constructs by decoupling the pattern spatially through mask design or temporally through innovative processes. This paper details a set of solutions that have enabled early 22 nm learning through careful lithography-design optimization.